User manual OLYMPUS CAMEDIA C-2040 ZOOM QUICK START GUIDE

[. . . ] Press on the Arrow pad to move the green highlighting frame so that "MODE SETUP" is selected. Then press . Lens 5-Pin external flash socket "SETUP" appears on the Monitor. Press the [OK] button. DC IN jack The MODE SETUP screen appears. AF/MF DRIVE Slide the battery compartment lock back to . Video output jack USB connector AF AUTO AUTO CARD SETUP MODE SETUP A/S/M MODE ALL RESET SETUP WB +- WB ISO SHARPNESS CONTRAST [3/3] ON RED · · · x · · · BLUE NORMAL NORMAL [1/4] O AE LOCK Connector cover [1/3] Menu screen 1/3 Menu screen 3/3 MODE SETUP screen 1/4 6. Press ) Mode dial Arrow pad Shutter button on the Arrow pad to select and then press . Flash mode button ( Erase button ( ) * * When you close the battery compartment cover, press down on the cover to hold the batteries down. [. . . ] Press the [OK] button repeatedly until you exit the menu screen. AF target mark Diopter adjustment dial 1AG6P1P0910--B VT2268-03 http://www. olympus-europa. com q Quick Start Guide q Manual focus Flash mode Slow synchro Flash intensity control Battery check Macro mode Card error White balance /M OD E A/S /M C-2040ZOOM Hotline Numbers Tel. 01805-67 10 83 for Germany Tel. 00800-67 10 83 00 for Austria, Belgium, Denmark, France, Netherlands, Norway, Sweden, Switzerland, United Kingdom Tel. +49 180 5-67 10 83 for Finland, Italy, Luxemburg, Portugal, Spain, Czech Republic Tel. +49 40-237 73 899 for Greece, Croatia, Hungaria and the Rest of Europe Our Hotline is available from 9 a. m. (Monday to Friday) (E-Mail) di. support@olympus-europa. com You can display images marked with the icon as movies. Press the (Menu) button and use the Arrow pad to select "MOVIE PLAY" and then press . When the movie ends, press the (Menu) button to display the menu and then press the Menu button again to exit Movie playback mode. · When a movie is running, you can use the Arrow pad to do the following: : Jump to the start of the current movie. FUNCTION : Play the movie in reverse for as long as the button is CARD SETUP MODE held down. Press this button again after the movie has finished to play the movie again. 2. Look through the viewfinder and point the camera at the person or object you want to photograph (the subject). Position the AF target mark over the subject. You can also look at the image on the Monitor to take pictures. Press the (Monitor) button to switch the Monitor on and off. Viewfinder AF target mark [To zoom in] By turning the zoom lever to "T", you can enlarge the picture of your subject. When you turn the zoom lever towards "W", the image reverts to the size it was when you switched the camera on, allowing you to shoot a wider area. 3. (Press the shutter button down halfway. ) With the camera pointed at your subject, press the shutter button down lightly. The green lamp beside the viewfinder lights. At this point, the focus and exposure (shutter speed and aperture setting) are locked. If the green lamp blinks, this indicates that the camera cannot focus. Release the shutter button, move the position of the AF target mark slightly and then lightly press the shutter button again. Half pressed Fully pressed AF target mark Green lamp 4. (Press the shutter button down fully. ) With the shutter button pressed down halfway, press it down further so it is fully depressed. The camera gives a short beep and takes the picture. The camera then starts recording the image onto the card and the card access lamp blinks. If the green lamp light up when you press the shutter button, you can take another picture, even if an image is being recorded onto the SmartMedia card. If you are taking a picture in low-light conditions, the flash will fire automatically. Card access lamp When your subject is not in the center of the shot (focus lock) First, position the AF target mark over your subject and press the shutter button halfway to focus the camera. Then hold the shutter button down as you move the camera to compose the shot as you want it and, without releasing the shutter button, press the shutter button down fully to take the shot. IA D L 1. [. . . ] You Memory can continue shooting when the lamp stops blinking and the gauge camera finishes recording data onto the card. AF target mark INFO FUNCTION CARD SETUP MODE SETUP YES NO 3. Viewing Your Shots Set the Mode dial to . HQ [1/1] YES OK NO This screen shows the still picture playback menu. Confirmation screen * The most recent shot is displayed on the Monitor (Single-frame playback). · Use the Arrow pad to select the image you want to view. : Displays the previous shot. : Jumps forward 10 shots. Arrow pad 1234 1235 5. Switch the camera off when you've finished shooting. 23. 12. , 00 21:56 6453 Always switch the camera off when you have finished taking pictures. [. . . ]