User manual PANASONIC CZRD513C

[. . . ] When AUTO is set, the louver swing mode can be selected from standard, upward and downward. Note: During DRY operation, it is normal that the louver movement may not follow remote control display OFF/ON Indicator LED This indicator lights up when the air conditioner is running. Message Display ODOUR WASH - Lights up during odour wash (odour removing) operation and flashes while odour wash (odour clear) is being set. NOT AVAILABLE - Lights up when the function is not available for operation. [. . . ] Example: Current Day is Wednesday and Current Time is 8:00 OFF/ON button This button is used to run or stop the air conditioner. Fan Speed button This button is used to change fan speed to Auto, Low, Medium and High. REMOTE LOCAL HEAT FAN COOL PRIORITY 1 2 3 4 5 6 FAN SPEED MON TUE WED THU FRI SAT SUN AUTO TIMER AIR SWING ECO OFF ADDRESS A/C No. ODOUR WASH CHECK SET AUTO 123 TEST RUN NOT AVAILABLE VENT. PRE HEAT DEFROST DEMAND ON LO MED HI AUTO HEAT FAN COOL DRY FILTER RESET Operation Mode button This button is used to change operation mode to "FAN", "COOL", "DRY", "AUTO" and "HEAT". Temperature Setting button This button is used to set the room temperature. 1 2 Turn on the power supply Press "SELECT button" TIMER/CLOCK MODE UP SET OFF / ON TEMP/ A/C No. UP TIMER/CLOCK MODE UP SET FAN SPEED MODE SELECT DOWN CANCEL AUTO MANUAL DOWN Manual Airflow Direction Selection button Fix the airflow direction manually. Filter Reset button After the filter has been cleaned, press this button to clear the "FILTER RESET" display. Auto Airflow Direction Selection button This button is used to select "Multi Comfort Air Control" (Automatic louver swing direction). Ventilation button When a ventilating device (optional) is attached, this button is used to run and stop the ventilating device. Economy button This button is used to run and stop the economy operation. SELECT DOWN CANCEL ECONOMY CHECK ODOUR WASH AIR SWING VENTILATION TEST RUN FILTER RESET Below displays will appear MON "MON" and "12:00" will be blinking 3 4 Select Current Day To set the current day, press "UP or DOWN button" to select current day. (Refer to above example; select WED) To confirm the selected day, press "SET button". Select Current Time To set the current time, press "UP or DOWN button" to select current time. (Refer to above example; select 8:00) To confirm the selected time, press "SET button". Odour Wash button This button is used to run and stop the odour wash (odour removing) operation. Long pressing of this button starts odour wash (odour clear) operation. Timer Setting button Group This button group is used for timer setting. Basic functions of each button are as follows: MODE - Changes clock and timer display or goes back to the previous display SELECT - Starts timer setting mode UP - Increases the time DOWN - Decreases the time SET - Confirms general settings and timer setting. Cancels all the timer settings collectively. Note : - Press "UP button" to increase or "DOWN button" to decrease (interval 1 minute) or hold the button to change the time faster. - If the "UP or DOWN button" is not pressed for 30 seconds during the day or time setting or if the "SELECT button" is pressed, the setting at that moment is confirmed and setting will end. Final CLOCK Display WED ":" will be blinking 3 4 How to Select the Timer 2 types of Timer mode can be selected on the remote control. - Daily Timer - Weekly Timer These timers cannot be operated simultaneously. Select one of these Timers for your convenience. Daily Timer Setting Display Will light up if Timer operation is selected TIMER ON-Timer To automatically switch "ON" the unit How to Change the Display MODE ON OFF OFF-Timer. To automatically switch "OFF" the unit Time to be selected (interval 10 minutes) - Press once to change the display from CLOCK to Timer or vice-versa. [. . . ] Only Saturday: 1st program ON 10:00 with 20°C & 2nd program OFF 14:00. No need to set any Timer. Day to be selected ON-Timer To automatically switch "ON" the unit 123456 MON TUE WED THU FRI SAT SUN TIMER Indicate the selected day Time to be selected (interval 10 minutes) ON OFF OFF-Timer. To automatically switch "OFF" the unit How to Set Weekly Timer - You can set the Timer for 1 week (Monday to Sunday) with 6 programs per day. - You also may select Collective - many days with same time setting or Individual ­ single/one day setting. MON TUE WED THU FRI SAT SUN To set A (Monday to Friday ­ Collective day setting) Press "SELECT button", To select Monday to Friday, deselect Saturday and Sunday by pressing "UP or DOWN button" to Saturday, press "SET button" (triangle mark on top of Saturday will disappear) Follow the same step to deselect Sunday. [. . . ]