User manual PANASONIC KX-DT346 QUICK REFERENCE GUIDE

[. . . ] G AUTO DIAL/STORE: Used for System/Personal Speed Dialing or storing program changes. 3 Location of Controls H TRANSFER: Used to transfer a call to another party. J MESSAGE: Used to leave a message waiting indication or call back the party who left the message waiting indication. K Headset Jack L FLASH/RECALL: Used to disconnect the current call and make another call without hanging up. Q Navigator Key: Used to adjust the volume and the display contrast or select desired items. [. . . ] Locking the Handset Hook Pull down the handset hook until it locks to prevent the handset from falling off the handset cradle when the unit is mounted to a wall or set at a high angle. To temporarily place the handset down during a conversation, hook it over the top edge of the unit as shown. 12 Document Version 2009-03 Connection Connection <Back view> Connect to: a digital proprietary telephone -- Digital XDP connection a single line telephone -- XDP or parallel connection The telephone line cord (included) Connect to a PBX. Clamp Headset Recommended: KX-TCA86, KX-TCA91, KX-TCA92 Do not use a KX-T7090 headset. Consult your dealer for more details about XDP and Digital XDP. CAUTION: When connecting a headset When connecting cords Ensure that the headset cord is wound around the hook to prevent damage to the connector. Ensure the cords are inserted in the grooves, and are clamped to prevent damage to the connectors. Document Version 2009-03 13 Installing KX-DT301/KX-NT303 Installing KX-DT301/KX-NT303 CAUTION: To prevent damage to the telephone, be sure to unplug the extension line before you set up or remove the KX-DT301 (USB Module) or the KX-NT303 (Add-on 12 Key Module). Connect the KX-NT303 first when installing both the KX-DT301 and the KX-NT303. KX-NT303 The Add-on 12 Key Module allows 12 additional flexible buttons to be added to this unit. These buttons are used to seize a CO line, make a call using One-touch Dialing, or perform a feature that has been assigned to the key. Attach the KX-NT303 to your unit with the screws (included with KX-NT303). 1. Plug the flat cable into the connector (A), then bend the cable slightly as shown (B). 4. Close the cover. 14 Document Version 2009-03 Installing KX-DT301/KX-NT303 KX-DT301 The USB Module can be connected between the DPT and the personal computer through USB interface to implement personal CTI (Computer Telephony Integration). Connect the USB cable to the USB port. Connect to a PC Ensure that the USB cable goes through the cable guide. Please use a USB cable shorter than 3 m (9 ft 10 in). Document Version 2009-03 15 Installing KX-DT301/KX-NT303 5. Attach the KX-DT301 to your unit with the screws (included with KX-DT301). 7. Refer to Installation Manual on the CD-ROM included with KXDT301. 16 Document Version 2009-03 Wall Mounting Wall Mounting 1. Set the operation board to level 1, then connect and secure the telephone line cords. The cords can also be run from the top of the unit (page 13). 3. Attach the wall mounting adaptor as shown. Make sure the cords are not pinched by the wall mounting adaptor. It also should not be placed in rooms where the temperature is less than 5 C (41 F) or greater than 40 C (104 F). Allow 10 cm (3-15/16 in) clearance around the unit for proper ventilation. Placement 1) Do not place heavy objects on top of this unit. 2) Care should be taken so that objects do not fall onto, and liquids are not spilled into, the unit. Do not subject this unit to excessive smoke, dust, moisture, mechanical vibration, shock, or direct sunlight. 3) Place the unit on a flat surface. 18 Document Version 2009-03 Important Information WARNING: TO PREVENT POSSIBLE FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS UNIT TO RAIN OR MOISTURE. THIS HANDSET EARPIECE IS MAGNETIZED AND MAY RETAIN SMALL FERROUS OBJECTS. [. . . ] To comply with FCC RF exposure requirements, it must be installed and operated in accordance with provided instructions. The unit requires minimum 20 cm (8 in) spacing must be provided between antennas and all person's body (excluding extremities of hands, wrists and feet) during wireless modes of operation. This transmitter must not be colocated or operated in conjunction with any other antenna or transmitter. Customer Information This equipment complies with Part 68 of the FCC rules and the requirements adopted by the ACTA. On the bottom of the cabinet of this equipment is a label that contains, among other information, the following product identifier: US: ACJKXNANKX-DT346 If requested, this number must be provided to the telephone company. [. . . ]