User manual PANASONIC KX-TG6461E

[. . . ] TG6461E(e). book Page 1 Monday, March 16, 2009 8:50 AM Operating Instructions Digital Cordless Answering System Model No. KX-TG6461E Thank you for purchasing a Panasonic product. You must subscribe to the appropriate service offered by your service provider/telephone company. Please read these operating instructions before using the unit and save them for future reference. TG6461E(e). book Page 2 Monday, March 16, 2009 8:50 AM Table of Contents Introduction Accessory information. 35 2 TG6461E(e). book Page 3 Monday, March 16, 2009 8:50 AM Introduction Accessory information Supplied accessories No. [. . . ] i M i {ih} Incoming call barring (Caller ID subscribers only) This feature allows the unit to reject calls from specified phone numbers that you do not want to answer such as junk calls. When a call is received, the unit does not ring while the caller is being identified. If the phone number matches an entry in the call barred list, the unit sends out a busy tone to the caller, and then disconnects the call. Program this setting using either the base unit or one of the handsets. Important: L When the unit receives a call from a number that is stored in the call barred list, the call is logged in the caller list (page 27) with 7 after the call is disconnected. Storing unwanted callers You can store up to 30 phone numbers in the call barred list by using the caller list or by entering the numbers directly. Important: L It is advised to store the phone number with an area code in the call barred list. 6 7 8 Enter the desired date and month. i M L We recommend selecting a different ringer tone to the one used for outside calls. M i {ih} L When the alarm is set, E is displayed. 9 Note: L You can skip to step 4 by pressing {R/E} in standby mode. L To stop the alarm, press any dial key or place the handset on the charger. L When the handset is in use, the alarm will not sound until the handset is in standby mode. L If you select "Once", the setting changes to "Off" after the alarm sounds. 24 Helpline Tel. 01289 8333 TG6461E(e). book Page 25 Monday, March 16, 2009 8:50 AM Programming = Base unit From the caller list: Erasing a number: W i {V}/{^}: "Yes" i M i {b} Y Handset 1 2 3 4 1 2 3 4 \ (right soft key) {V}/{^}: Select the entry to be barred. i 8 {V}/{^}: "Add Bar List" i M {b} 1 2 3 4 8 (middle soft key) {V}/{^}: "Caller Barred" i M {V}/{^}: Select the desired entry. Editing a number: 8 i {V}/{^}: "Edit" i M i Edit the phone number. i M i {ih} Erasing a number: W i {V}/{^}: "Yes" i M i {ih} By entering phone numbers: 8 (middle soft key) {V}/{^}: "Caller Barred" i M i ~ Enter the phone number (24 digits max. ). {b} Y Handset From the caller list: Note for base unit and handset: L When editing, press the desired dial key to add, ^ to erase. 1 2 3 4 5 1 2 3 4 8 (middle soft key) {V}/{^}: "Caller List" i M {V}/{^}: Select the entry to be barred. i 8 {V}/{^}: "Add Bar List" i M {ih} 8 (middle soft key) {V}/{^}: "Caller Barred" i M i ~ Enter the phone number (24 digits max. ). {ih} Registering a unit Operating additional units Additional handsets Up to 6 handsets can be registered to the base unit. Important: L The additional handset model recommended for use with this unit is noted on page 3. If another handset model is used, certain operations (base unit settings, handset settings, etc. ) may not be available. By entering phone numbers: Viewing/editing/erasing bar call numbers = Base unit Registering a handset to the base unit The supplied handset and base unit are preregistered. If for some reason the handset is not registered to the base unit (for example, w flashes even when the handset is near the base unit), reregister the handset. 1 2 3 4 8 (middle soft key) {V}/{^}: "Caller Barred" i M {V}/{^}: Select the desired entry. [. . . ] L If your own greeting message is not recorded properly, callers may not leave a message. L If you subscribe to a voice mail service, messages are recorded by your service provider/telephone company, not your telephone. Change the unit's number of rings setting or contact your service provider/telephone company (page 33). If you have forgotten your remote access code, enter the remote access code setting to check your current code (page 31). [. . . ]