User manual PANASONIC KXTG6521E

[. . . ] TG6511-6521E(e). book Page 1 Monday, January 11, 2010 8:48 AM Operating Instructions Digital Cordless Phone Model No. KX-TG6511E KX-TG6512E KX-TG6513E KX-TG6521E KX-TG6522E KX-TG6523E KX-TG6524E Digital Cordless Answering System Model No. Model shown is KX-TG6511. Before initial use, see "Getting Started" on page 11. Thank you for purchasing a Panasonic product. Please read these operating instructions before using the unit and save them for future reference. You must subscribe to the appropriate service offered by your service provider/telephone company. Please access our online customer survey: http://panasonic. net/pcc/tel/q TG6511-6521E(e). book Page 2 Monday, January 11, 2010 8:48 AM Table of Contents Introduction Model composition . [. . . ] *7 Turn this feature off if you prefer not to hear key tones while you are dialling or pressing any keys, including confirmation tones and error tones. *8 If you subscribe to a Caller ID service and want to view the caller's information after lifting up the handset to answer a call, turn off this feature. *9 The recall/flash time depends on your telephone exchange or host PBX. *10To prevent other users from joining your conversations with outside callers, turn this feature on. 26 Helpline Tel. 01289 8333 TG6511-6521E(e). book Page 27 Monday, January 11, 2010 8:48 AM Programming Special programming Alarm An alarm sounds at the set time for 3 minutes once or daily. Important: L Set the date and time beforehand (page 16). Changing the handset name Each handset can be given a customised name ("Bob", "Kitchen", etc. ). You can also select whether or not the handset name is displayed in standby mode. If you select "On" without entering any handset name, "Handset 1" to "Handset 6" is displayed. 1 2 8 i {#}{7}{2}{0} {V}/{^}: Select the desired alarm option. Go to step 4. 1 2 3 4 5 8 i {#}{1}{0}{4} Enter the desired name (max. i M 2 times {ic} 3 4 5 Incoming call barring (Caller ID subscribers only) Available for: KX-TG6521/KX-TG6522/ KX-TG6523/KX-TG6524 This feature allows the unit to reject calls from specified phone numbers that you do not want to answer such as junk calls. When a call is received, the unit does not ring while the caller is being identified. If the phone number matches an entry in the call barred list, the unit sends out a busy tone to the caller, and then disconnects the call. Important: L When the unit receives a call from a number that is stored in the call barred list, the call is logged in the caller list (page 30) with 7 after the call is disconnected. Enter the desired date and month. i M L We recommend selecting a different ringer tone from the one used for outside calls. M i {ic} L When the alarm is set, E is displayed. 6 Note: L To stop the alarm, press any dial key or place the handset on the base unit or charger. L When the handset is in use, the alarm will not sound until the handset is in standby mode. Helpline Tel. 01289 8333 27 TG6511-6521E(e). book Page 28 Monday, January 11, 2010 8:48 AM Programming Storing unwanted callers You can store up to 30 phone numbers in the call barred list by using the caller list or by entering the numbers directly. Important: L You must store the phone number with an area code in the call barred list. From the caller list: Changing the base unit PIN (Personal Identification Number) Important: L If you change the PIN, please make note of your new PIN. If you forget your PIN, see page 44. 1 2 3 4 1 2 3 {<} (y) {V}/{^}: Select the entry to be barred. i I {V}/{^}: "Caller Barred" i M {V}/{^}: "Yes" i M i {ic} 8 i {#}{2}{1}{7} i m Enter the phone number (24 digits max. ). {ic} 1 2 3 8 i {#}{1}{3}{2} Enter the current 4-digit base unit PIN (default: "0000"). [. . . ] L If you subscribe to a voice mail service, messages are recorded by your service provider/telephone company, not your telephone. Change the unit's number of rings setting or contact your service provider/ telephone company (page 36). If you have forgotten your remote access code, enter the remote access code setting to check your current code (page 35). Turn it on (page 36). My own greeting message cannot be properly heard. [. . . ]