User manual PANASONIC WJ-HD200

DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!

If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Diplodocs provides you a fast and easy access to the user manual PANASONIC WJ-HD200. We hope that this PANASONIC WJ-HD200 user guide will be useful to you.


PANASONIC WJ-HD200 : Download the complete user guide (3153 Ko)

Manual abstract: user guide PANASONIC WJ-HD200

Detailed instructions for use are in the User's Guide.

[. . . ] Digital Disk Recorder Operating Instructions Model No. WJ-HD200 ENGLISH OPERAT E ALARM TIMER SUSPEN D REMOTE RESET LOCK DST SPOT MULTI CAMERA SELECT OSD 1 SEQUEC E 2 6 3 7 HDD 4 8 MULTISCR EEN SELECT FULL ERROR ZOOM 5 SETU /ESC P STOP PLAY REC REC STO P ALARM SERCH TIME&D ATE SEARCH PLAY MOD E SERECT ALARM RECALL PUSH­ PAUSE SET Digital Dis k Recorde r WJ-HD2 00 Before attempting to connect or operate this product, please read these instructions carefully and save this manual for future use. FRANÇAIS ENGLISH VERSION Caution: Before attempting to connect or operate this product, please read the label on the bottom. CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. For U. S. A SA 1965 The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance. NOTE: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. [. . . ] This selection enables the DATA terminal on the rear panel for communication. This selection enables the RS-232C terminal on the rear panel for communication. Note: Parallel use of the DATA and RS-232C terminals is not possible. q e w r 36 G Baud Rate (BAUD RATE) 1. 4800: 4 800 bps 9600: 9 600 bps* 19200: 19 200 bps OFF: Retransmission is disabled. * 100MS: 100 m seconds 200MS: 200 m seconds 1S: 1 second G Control Unit Address (CTL-UNIT ADDRESS) (only for PS ·DATA) When the recorder performs as a controller in the system, the unit address can be set from the setup menu on the monitor. Note: Assign an address except 1 to WJ-HD200 when using a system controller in the system. G Data Bit (DATA BIT) 1. NONE: No parity check EVEN: Even parity ODD: Odd parity* G System Unit Address (SYS-UNIT ADDRESS) (exclusive to PS · DATA) When the recorder performs as a system unit, the unit address can be set from the setup menu on the monitor. 1: 1 bit* 2: 2 bits Assignable address: From 1 to 99, must be unique in the chain. G Alarm Data (ALARM DATA) (exclusive to PS · DATA) The recorder pauses before sending a notice to the connected system controller when an alarm operates. 5S: Pauses 5 seconds. G Wait Time (WAIT TIME) The unit retransmits data after waiting the specified time if there is no response from the connected device. SETUP) (exclusive to PS · DATA) Camera numbers will be used in a PS·DATA chain when you select a camera to control it from a system controller. SETUP menu opens. I Network Setup (NETWORK SETUP) NETWORK SETUP LINE SPEED AUTO HTTP PORT 00080 DHCP OFF IP ADDR 192. 168. 000. 010 NETMASK 255. 255. 255. 000 GATEWAY 192. 168. 000. 001 CAM NO. SETUP CAM-PORT 1 2 3 4 5 6 7 8 CAM NO. 001 002 003 004 005 006 007 008 Note: The system will restart after the menu setup window is closed when any parameter in this window has been changed. G Line Speed (LINE SPEED) 2. Assignable numbers: From 001 to 128, each number must be unique in the chain. 100M_FULL: 100 mega byte, full duplex 100M_HALF: 100 mega byte, half duplex 10M_FULL: 10 mega byte, full duplex 100M_HALF: 10 mega byte, half duplex G HTTP Port (HTTP PORT) Set an HTTP port number. Available port numbers: From 00000 to 65535, except the "well-known port" numbers assigned by IANA (Internet Assigned Numbers Authority) G Dynamic Host Configuration Protocol (DHCP) Dynamic Host Configuration Protocol is enabled or disabled. Note: When ON is selected, you cannot enter the IP address, netmask, or gateway. The given parameters will be displayed after getting the IP address from the DHCP server. 38 G IP Address (IP ADDR) The default is "192. 168. 000. 010". G Sequence Setup (SEQUENCE SETUP) SEQUENCE SETUP MULTI SEQ SETUPO SEQUENCE TIMING INT AUTO SKIP ON SPOT SEQ SETUPO SEQUENCE TIMING AUTO SKIP INT ON G Netmask (NETMASK) The default is "255. 255. 255. 000". G Gateway (GATEWAY) The default is "192. 168. 000. 001". I Switcher Setup (SWITCHER SETUP) SWITCHER SETUP START DISPLAY QUAD-4A MULTI SEL MODE ALL SEQUENCE SETUPO CAMERA VIEW SETUPO 1. Move the cursor to SEQ SETUP in the SWITCHER SETUP menu, and press the JogDial. Select either MULTI SEQ SETUP or SPOT SEQ SETUP with the [D] or [C] button, and press the JogDial. The selected menu opens. G Multiscreen Sequence Setup (MULTI SEQ SETUP) Open the QUAD SEQ SETUP menu to program the sequence steps for displaying quad-split and single input images. MULTI SEQ SETUP Video switcher functions are programmed in this menu setup. G Start Display (START DISPLAY) The image in the selected form will be displayed on the monitor when the recorder is turned on. Single image: CH 1 to CH 8 Quad image: QUAD-4A (including 1-4), QUAD-4B (including 5-8) Multi image: 9SCREEN (including 1-8) Sequence: SPOT SEQ, MULTI SEQ STEP 1 2 3 4 5 6 7 8 CAM QUAD-4A QUAD-4B - SEC 2S 2S 2S 2S 2S 2S 2S 2S 1. Available cameras: From 1 to 8 individually, 4A(1-4), or 4B(5-8) Note: The recorder will skip any step assigned "­". [. . . ] Wait until the process ends. When YES is selected, the display will turn to NOW FORMATTING. It will change to HDD FORMAT SET DONE when formatting is completed. Notes: · The PLAY ONLY mode can be utilized when you verify a transplanted HDD removed from another disk recorder that malfunctioned. · In normal operation after selecting the PLAY ONLY mode, "STOP (PO)" appears in the status display while camera pictures are displayed, but not in playback. Press the JogDial to execute the selection, or press the [STOP] button to return to the above step 1. [. . . ]

DISCLAIMER TO DOWNLOAD THE USER GUIDE PANASONIC WJ-HD200




Click on "Download the user Manual" at the end of this Contract if you accept its terms, the downloading of the manual PANASONIC WJ-HD200 will begin.

 

Copyright © 2015 - manualRetreiver - All Rights Reserved.
Designated trademarks and brands are the property of their respective owners.