User manual PITSOS POWERJET4

[. . . ] en Operating instructions 9000 439 036 (8908) Dishwasher Reset 3 sec. 10 9 8 7 End Start 1 2 3 9h 6h 3h 5 6 4 20 21 22 23 24 25 26 27 28 en Table of contents Washing the dishes . 13 13 13 13 14 14 14 14 14 14 14 15 15 15 15 16 16 17 17 17 18 18 19 19 19 20 20 20 20 20 20 21 21 21 21 21 21 Safety instructions . 13 en Safety instructions Delivery ­ Check the packaging and dishwasher immediately for damage caused in transit. ­ Please dispose of the packaging material in an environmentally friendly manner. [. . . ] In the automatic programmes the temperature and running time can also be adjusted to the degree of soiling. · Hygiene * The temperature is increased during the cleaning process. chopping boards and baby bottles. ¿ Extra drying * An increased temperature during the final rinse and an extended drying phase ensure that even plastic parts dry better. There is a slight increase in the energy consumption. Switching on the appliance ­ Turn on the tap fully. he programme starts running. 13 en Timer programming * * depending on model You can delay the start of the programme by 3, 6 or 9 hours. ­ Keep pressing the Preselected starting time button @ until the appropriate display 3h, 6h or 9h is lit. ­ To delete the preselected starting time, keep pressing the Preselected starting time button @ until none of the displays 3h, 6h or 9h is lit. You can change your programme selection at any time until the programme starts. Terminating the programme (Reset) ­ Press START button 8 for approx. Switch off ON/OFF switch (. Changing the programme When the START button 8 has been pressed, the programme cannot be changed. The only way a programme can be changed is by Cancel programme (Reset). Intensive drying The final rinse uses a higher temperature which improves the drying result. ­ Rotate programme selector 0 until the "Check water supply" display ` flashes. To change the setting, ­ By rotating the programme selector 0, you can switch on intensive drying (End displayh is lit) or switch off intensive drying (End display h is not lit). The setting is saved. End of programme The programme has ended when the End display h is lit. Switching off the appliance Short time after the end of the programme: ­ Switch off ON/OFF switch (. ­ Remove the utensils when they have cooled down. ã=Warning At the end of the programme please open the door fully and not partially when emptying the dishwasher. Any escaping water vapour could damage sensitive worktops. Interrupting the programme ­ Switch off ON/OFF switch (. If the door was opened on an appliance which has a warm water connection or is heated, first leave the door ajar for several minutes and then close. Otherwise, expansion (pressure) may cause the appliance door to spring open or water to run out of the appliance. 14 en Maintenance and care A regular inspection and maintenance of your machine will help to prevent faults. This saves time and prevents problems. Filters The filters 1* keep large foreign objects in the rinsing water away from the pump. The filter system consists of a coarse filter, a flat fine filter and a microfilter. ­ Unscrew filter cylinder as illustrated and take out filter system. Overall condition of the machine ­ Check spray arm for grease and limescale deposits. If you find such deposits: ­ Fill detergent dispenser with detergent. Start the appliance without utensils in the programme with the highest rinsing temperature. [. . . ] These will disappear after the first wash cycle. Fresh water connection ­ Connect the fresh-water connection to the tap according to the installation instructions with the enclosed parts. Ensure that the fresh-water connection is not kinked, crushed or twisted. ­ When replacing the appliance, always use a new water supply hose. 24 kg Voltage: 220­240 V, 50 Hz or 60 Hz Connected load: 1. 9­2. 3 kW Fuse: 10/16 A Water pressure: at least 0. 05 MPa (0. 5 bar), maximum 1 MPa (10 bar). [. . . ]