User manual PITSOS WFPI1000D

[. . . ] Start time indicator Ýôïéìï óå and Òñá (h) . Cleaning the outside of the appliance, the control panel and the pipes . 4 5 6 7 7 7 9 10 10 10 11 11 12 13 15 16 18 19 19 20 20 21 21 22 23 23 23 23 24 25 26 2 Help with small problems . . 27 27 32 33 34 34 34 34 35 36 36 36 38 39 40 41 42 Installation Instructions Assembly, connection and transport . [. . . ] As soon as water starts going in: q Gently pull the drawer out and q pour the dissolved starching agent into compart ment I. If L has been selected, now activate Üíéëçóç. 22 Cleaning and care d Danger of electric shock Always disconnect the appliance from the mains be fore cleaning it. d Danger of explosion Never use solvents to clean. Cleaning the outside of the appliance, the control panel and the pipes. Cleaning the drum If necessary: q Use a little soapy water or a soft, non-abrasive detergent. q Dry with a soft cloth. If rust marks are appearing that are caused by metal objects (e. g. coins, clips, safety-pins, etc. ): q Use non-chlorine cleaning products; Follow the manufacturer's instructions. Never use steel wool. Removing limescale from the appliance Warning!Products for removing limescale contain acids which may damage the appliance's components or cause discolouration in the laundry. Removing limescale is not normally necessary if the correct dosage of detergent has been used. However, if it becomes necessary to remove the lime scale, the instructions provided by the limescale re moving product should be followed closely. 23 Clean the detergent drawer When detergent or additive residue has built up: q Pull the drawer out fully, q press on the moveable part, and q completely remove the drawer from the appliance. q Pull moveable part. upwards. q Clean the drawer with running water and dry it. q Close the moveable piece and fix it. q Put the drawer back in. 24 Clean the drainage pump Emptying the wash water If the wash water is not completely emptied. Foreign objects are blocking the drainage pump or laundry with a lot of loose threads has been washed. (up to 20 litres, a suitable container is needed) d Danger of scalding First allow the wash water to cool. q Open and pull out the service hatch. q Take the drainage pipe out of its housing and re move it from the appliance. 90 °C max. q Remove the lid carefully and let the wash water flow into the receptacle. q Fit closure plug and attach the drainage pipe to its fitting. q Carefully unscrew the pump's cap. Remove remains and loose threads from the thread of the pump cap and pump housing. To avoid detergent being discharged in the next wash without having been used: q Put 1 litre of water into the drum II. q Select programme Üíéëçóç. 25 Clean the filter in the appliance's water inlet d Danger of electric shock If no water, or only very little, is admitted into the ap pliance. First clear the pressure that has built up in the freshwater hose: q Close the tap. q Set the programme selector to any wash program me (except óôýøéìï/Üíéëçóç) q Press the Ýíápîç M button and let it work for around 40 seconds. q Set the programme selector to the stop position. Clean the water tap filter q Pull the hose from the tap. [. . . ] q Connect the inlet hose to the water tap: q to the union at the back of the appliance . . . q and to the water inlet (tap). 10 mm 39 Emptying the water Important Do not bend or pull the hose. Difference in height between the support surface and water outlet: minimum 60 cm, maximum 100 cm. Drainage through a U-bend: q Secure the connection point using a Ø 24-40 mm clamp (from a specialist outlet). Drainage to a sink: Important Check that the cap does not obstruct the sink's drai nage. [. . . ]