User manual PLEXTOR PX-EH25L QUICK SETUP GUIDE

[. . . ] IMPORTANT! When Turning Off the Power. . . 1 Turn off the POWER switch on the rear of the PX-EH. If the switch is already off, turn it on and then off again. If you already have the environment specified below, you can start using your PX-EH simply by making the necessary connections. You need a network having a DHCP server* equipment (broadband router, router-type DSL modem, etc. ), as illustrated below. Before Setting Up. . . Power off 2 The shut down will start. Check the POWER lamp (green) on the front of the PX-EH. Start blinking (Shut down is started) All unsaved data are written to the internal or external hard disk drive. [. . . ] (Turn this page for an explanation on how to read the Online Manual. ) 2 Check the computer you are using. If you have the above environment, turn this page to proceed to page 2. 6 7 Confirm that a LAN interface is installed and operating properly. 1 Connecting the PX-EH to a network. This PX-EH is designed for installation in vertical orientation. Connect the PX-EH after confirming that the DHCP server is operating. Turn on the power. 1 2 Connet the AC Adapter to DC of the PX-EH and the power socket. If the switch is already on, such as when the PX-EH was shut down from the setup screen after the last session, turn off the switch and then turn it back on. The PX-EH has been powered up when the POWER lamp on the front of the PX-EH turns to a steady green light. If the POWER lamp does not turn to a steady green light, refer to "Troubleshooting in the Online Manual" provided separately. 15 seconds Power on Access the PX-EH. Example of accessing from a Windows XP computer How to Read the Online Manual The Online Manual is provided as a HTML document. We recommend that you view the Online Manual in Internet Explorer Version 5. 0 or higher. 1 1 Set the MDI/MDI-X selector switch on the rear of the PX-EH in accordance with the network equipment to which the PX-EH is connected. Click Start, right-click My Network Places, and then click Search for Computers. 2 Enter "PX-EH" under Computer name, and then click the Search button. Windows Click Set the supplied CD-ROM in your computer. If the menu is not displayed automatically, open the CD-ROM from My Computer, etc. , and then double-click top. htm Mac Connected network equipment 3 MID-X port of computer or hub Hub 1 Enter "PX-EH" Set the supplied CD-ROM in your computer. Double-click top. htm Selector Switch 2 Click Double-click PX-EH series "PXEH", which will be found as a result of search. Double-clicking the disk folder will open the usable folders in the PX-EH. LAN port MDI-X MDI 3 Steady light 4 Tip When you open online manual on Windows XP SP2, a pop-up message, "Information Bar", may appear. If it appear, please check "Do not show this message again" and click "OK". Online Manual will be displayed. MDI/MDI-X selector switch Connect one end of the supplied LAN cable to the LAN port of the PX-EH, and then connect the other end to the network equipment. Connect one end of the LAN cable to the LAN port on the rear of the PX-EH. Connect the other end to the network equipment. Start blinking The blinking period will vary depending on the condition of the PX-EH. 2 Check Click Double-click Double-click Please click information bar between the toolbar and the content window in Internet Explorer and click "Allow Blocked Content. . . ". Network equipment A steady green color of the POWER lamp indicates that the setup is complete! [. . . ] If the PX-EH is powered up before the LAN cable is connected, the PX-EH cannot participate in the network properly. While the PX-EH is operating, do not turn off the power by disconnecting the power cable or turning off the AC tap with switch without completing the shut down process. Doing so may result in breakdown or cause loss of data. Click 2 3 4 5 [. . . ]