User manual PLEXTOR PX-PA15AW SOFTWARE

[. . . ] All sample images and electronic files included in the documentation and distribution materials are copyrighted by their respective photographers and are not to be copied or reproduced in any manner. Trademarks Windows 2000, Windows XP, and Microsoft are registered trademarks of Microsoft Corporation. All other trademarks are the properties of their respective owners. ii Contents Chapter 1 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 System Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Hardware Box Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Chapter 2 Setting Up the System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Chapter 3 Using Presto!WMS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 Appendix Channel Specifications. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 Note: During Software installation PX-PA15AW is referred as WMS Image 100. iii Chapter 1 Introduction The Plextor PX-PA15AW Wireless Projector Adapter uses Presto!You need a projector or monitor for the adapter, and a computer to act as Sender. [. . . ] Click "Install software" button and then the installation program will start. After installing the software, the system will detect the related hardware and install the driver. WMS software is now ready to use. 3 Chapter 2 Setting Up the System Here is how to prepare the program for a presentation. Click OK to start scanning for channels, and then scanning for the adapters. 4 Chapter2 Setting Up the System This scanning process only happens when (1) opening Presto!WMS will recognize the previously connected device when opening and skip the device scanning. If the previously connected device has been removed, a message will open and device scanning will be done again. For WLAN cards that have yet to pass the Windows certification, the scanning process won't find the adapter. This message will appear to help you find a solution: "WMS is unable to connect to the receiver with the Windows Standard Utility. To begin using the software, please use your Windows WLAN card utility to manually locate a wireless connection to the receiver". If you used the WLAN Card utility to manually locate a wireless connection to the receiver, you can start to play. Otherwise an adapter won't be found. " For Ethernet, the scanning process won't start and the main control panel will open. Click one to select it. 5 Chapter2 Setting Up the System You can select more than one adapter. If Multiple Adapters is selected, there will be a check box for each device on the Adapter List. Click the box. button on the control panel to open the Settings dialog 6 Chapter2 Setting Up the System 5. Multiple Adapters: Enable this option to select more than one adapter for transmission. There won't be a check box in front of the listed adapters if this option is not enabled. Search: Click this button and the program will scan again for available adapters. 7 Chapter2 Setting Up the System If the network device is Ethernet or the WLAN card has not passed the Windows NDIS certification, the functions on the Adapter tab will be disabled. Click the Quality tab to set up the screen capture quality supported by Presto!The better the quality is, the more likely the stream transmission will be slowed. Monitor Resolution: Click to choose the screen capture resolution. The default Color Quality is Normal, and the default Monitor Resolution is 1024 x 768. 8 Chapter2 Setting Up the System 7. Click the WEP tab to use Wired Equivalent Privacy and add protection to your data. [. . . ] A connection is being provided by the Access Point using the WEP key settings. The connection status icons and the connected device name will only appear when using a WLAN card that has passed the Windows NDIS certification. If not, or the connection device is Ethernet, the status bar will be blank. 11 Appendix Channel Specifications This program is based upon the IEEE 802. 11 standards. For 802. 11a, it uses the 5 GHz band, and for 802. 11 b and g, it is the 2. 4 GHz band. [. . . ]