User manual PROEL PLLED150

[. . . ] This product should not be mixed with other commercial wastes for disposal. The lightning flash with arrowhead symbol within an equilateral triangle is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure, that may be of sufficient magnitude to constitute a risk of electric shock to persons. CAUTION - Before using this product read carefully the following safety instructions. Take a look of this manual entirely and preserve it for future reference. [. . . ] It adjusts the level of the channel signal and sends it to the MAIN MIX (if the MIX button is pressed) and to GROUP 1-2 or 3-4 (if the 1-2 or 3-4 buttons are pressed). Rotate this detented switch to select the preset effect you want to use. Dense, smooth reverb with long tail, long pre delay and some early reflections. The VARIATIONS vary from "bright" (1-8) to "warm" (9-16) starting from long tail to short tail for each one. Dense, smooth reverb with short tail, normal pre delay and increased early reflections. The VARIATIONS vary from "bright" (1-8) to "warm" (9-16) starting from long tail to short tail for each one. LARGE ROOM - This type of reverb reproduces the more intimate ambience of natural room acoustics. The VARIATIONS vary from "bright" (1-8) to "warm" (9-16) starting from long tail to short tail for each one. SMALL ROOM - This type of reverb reproduces the more intimate ambience of natural room acoustics. The VARIATIONS vary from "bright" (1-8) to "warm" (9-16) starting from long tail to short tail for each one. The VARIATIONS vary from "bright" (1-8) to "warm" (9-16) starting from long tail to short tail for each one, alternating hall, tape, spring or plate types of reverb. Engage this switch if you want to mute the signal coming from the FX1 internal effect. You can connect a footswitch to MUTE both the FX1 and FX2 internal effects, suggested footswitches are PROEL model PFS20, PFS24, PFS29. NOTE: the FX1 and FX2 mutes change status each time the footswitch is pressed, in other words if both effects are ON they became both AFF, if one effect is ON and the other is OFF, they became OFF and ON respectively. Use these unbalanced RCA connectors to patch the output of a player, such as an analog tape deck, a DAT, a MD or a CD player. IMPORTANT: this input and the USB input are routed together, so we suggest to use only one of them at the same time. It adjust the level of the 2TRK INPUT and USB input (audio signal from a PC). Typically this button must be released to avoid problems with feedbacks when you use the mixer for recording the signal of the MIX bus. Use these unbalanced RCA connectors to send out the MAIN MIX signal to a recorder (such as an analog tape, a DAT or a MD recorder). Push in this switch to send the 2TRK input signal and USB input signal to C. NOTE: for a correct operation we suggest to choose these three switches (76) or (77) or (78) or (79) one at a time. IMPORTANT: these four switches also select which signal is displayed on LED METERS when none channel is soloed. [. . . ] Turn down: the MAIN MIX (108) fader level, the GROUP 1-2 / 3-4 (104) faders level, the C. In your DAW software make sure to set record tracks WITHOUT MONITORING during playback/recording (the method depends by your DAW software). Make sure these switches are UP: 2TRK TO MIX (74), GROUP TO MIX (105) MIX (76) otherwise you'll hear feedback when you turn up the MAIN MIX fader later. Set each recording channel's GAIN (4)(26) knobs and LEVEL (22)(43) fader so that you're getting good level without lighting the PEAK indicator on the mixer, also using the SOLO (21)(42) and SOLO MODE (113) PFL and AFL operations. [. . . ]