User manual PROEL PLLED155

[. . . ] This product should not be mixed with other commercial wastes for disposal. The lightning flash with arrowhead symbol within an equilateral triangle is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure, that may be of sufficient magnitude to constitute a risk of electric shock to persons. CAUTION - Before using this product read carefully the following safety instructions. Take a look of this manual entirely and preserve it for future reference. [. . . ] It adjusts the amount of channel signal sent to the left and the right outputs if the channel is used as MONO, or it fades the LEFT or RIGHT signal amount if the channel is used as STEREO. When you engage a channel's mute switch, its signal disappears from Questo controllo invia il segnale all'uscita ausiliaria AUX 3 e all'effetto these outputs: MAIN MIX, GROUPS 1-2, AUX 1, AUX 2, interno (DIGITAL EFFECT PROCESSOR). BAL (controllo bilanciamento) 12 kHz muted by this switch, so you can listen to it thru Regola la quantità del segnale da inviare alle uscite sinistra o headphones and C. ROOM outputs acting on the SOLO -15 +15 destra se il canale è usato in MONO, oppure riduce la quantità button in PFL mode only (see SOLO MODE). Engaging this switch you assign the channel signal to the MAIN MIX bus regulated by the MAIN MIX faders. Engaging this switch you assign the channel signal to the GROUP 1-2 bus regulated by the GROUP 1-2 faders. You can use the GROUP 1-2 jacks as separate outputs or, engaging the switch GROUP 1-2 TO MIX, to create a submix for a set of channels (all the drums channels, for instance): in this case you can control the assigned GROUP 1-2 signals together and independently from the rest of the mix. This LED has two function: If the PEAK LED lights permanently this means that you have activated the SOLO switch of this channel. If the PEAK LED flashes this means that the input signal is near to the CLIPPING point. IMPORTANT: if the LED PEAK flashes reduce the level of the input signal using the GAIN control. This switch allows you to hear signals through your headphones or control room outputs. Engage this switch if you want to mute the signal coming from the internal effect. NOTE: the effect can be turned on/off also using a footswitch connected to the FX MUTE jack socket. This LED shows 2 conditions: · Flashing = indicates a too high input level, near to the overload of the effect input stage. You can connect a footswitch to MUTE the mixer internal effect, suggested footswitches are PROEL model PFS20, PFS24, PFS29. Use it to reduce the level of signal sent to the internal effect is the PEAK LED is flashing. This control ranges from off through unity (the center detent position) on up to 15 dB of extra gain (fully clockwise). Typically, it is set to MIX if the internal effect is used only for channels assigned to MIX bus or to 1-2 if the internal effect is used only for channels assigned to 1-2 bus. Use these unbalanced RCA connectors to patch the output of a player, such as an analog tape deck, a DAT, a MD or a CD player. IMPORTANT: this input and the USB input are routed together, so we suggest to use only one of them at the same time. It adjust the level of the 2TRK INPUT and USB input (audio signal from a PC). Typically this button must be released to avoid problems with feedbacks when you use the mixer for recording the signal of the MIX bus. [. . . ] If you PC has a level meter it must never reach the red color (0 dBFs) position to avoid any digital clip distortion. Turn down: the MAIN MIX (83) fader level, the GROUP 1-2 (80) fader level, the C. In your DAW software make sure to set record tracks WITHOUT MONITORING during playback/recording (the method depends by your DAW software). Make sure these switches are UP: 2TRK TO MIX (58), GROUP 1-2 TO MIX (81) otherwise you'll hear feedback when you turn up the MAIN MIX fader later. [. . . ]