User manual QSC AUDIO BASIS 902ZZ

[. . . ] BASIS 902zz 8 Output CobraNet Enabled Control and Monitoring Signal Processor Hardware Manual *TD-000146-00* TD-000146-00 rev. A IMPORTANT SAFETY PRECAUTIONS & EXPLANATION OF SYMBOLS The lightning flash with arrowhead symbol within an equilateral triangle is intended to alert the user to the presence of uninsulated "dangerous" voltage within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to humans. The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in this manual. This unit has been engineered and manufactured to assure your personal safety. Improper use can result in potential electrical shock or fire hazards. [. . . ] To connect the cable, orient the connector properly, then push into the receptacle until it is firmly seated; tighten the retaining screws "finger tight". Communications should be 9600 baud, no parity, 8 data bits, 1 stop bit, and flow control Xon/Xoff. When using the BASIS 902zz with QSC DataPort-equipped amplifiers or QSC DSP products (DSP-3, DSP-4) connect to the BASIS 902zz using QSC DataPort cables. The 902zz supports up to eight channels of DataPort audio and amplifier status monitoring. This can be four 2-channel amplifiers or one 8-channel amplifier or other suitable combinations. If connecting a multi-DataPort amplifier, ensure all the DataPorts of the amplifier are connected and that they are all connected to the same BASIS. To connect the cable, orient the connector properly, then push into the receptacle until it is firmly seated; tighten the retaining screws "finger tight". LED Indicators When the BASIS 902zz is plugged into a properly functioning AC outlet, it will power up and briefly display a welcome screen on the LCD display. POWER Indicator- This blue indicator illuminates when the BASIS 902zz is plugged into a properly functioning AC source. DIAGNOSTIC Indicator- This red indicator illuminates during the power-on self test, then should extinguish. If it remains illuminated, this indicates that the self-test has detected an unexpected event, such as corrupted firmware or a memory boot failure. If the DIAGNOSTIC LED remains illuminated, try resetting the BASIS 902zz by cycling power off and on once. Should the indication persist, contact QSC's Technical Services for guidance. During operation, any system fault will fully illuminate the indicator. During a "flash" update, the indicator will blink on and off; this is normal. For purpose of unit identification, the LED can be remotely turned on using QSControl. net software. (continued, next page) 15 LED Indicators (continued) QSControl and CobraNet Network Status (Port) Indicators- There is a group of three LEDs on the front and rear panels labeled RX, TX and LINK. One group is for the QSControl network port and the other for the CobraNet network port. Note: Port indicators on rear panel are color coded to match the corresponding color-ring around the QSControl and CobraNet RJ45s. RX (receive)- This indicator illuminates any time the BASIS 902zz receives data from the corresponding network. TX (transmit)- This indicator illuminates whenever the BASIS 902zz transmits data onto the corresponding network. LINK STATUS- The corresponding indicator illuminates when the BASIS 902zz is connected to an operating network. These indicators are either off, red, green, or yellow, depending on what is connected to the port. The indications are: off- nothing attached red- QSC DSP accessory attached green- QSC DataPort amplifier attached yellow- QSC DSP and Amplifier combination attached LCD Display and Controls The BASIS 902zz has a 2 line X 16 character LCD display. The display and the multi-function push-button switches on either side provide data access and editing capability. [. . . ] 2- If the address entered was correct and network communications with the BASIS 902zz are successful, the Telnet session should open. 3- Now you have the same options that are available in the Serial Port I/O (RS-232) interface section. 23 Preliminary Specification Dynamic Range (AES-17, -60dB Method, all sensitivities) unweighted >112db A weighted >115db Distortion (20Hz-20 KHz, all sensitivities) +4dBu (max) 2dB below clip (max) Crosstalk (20Hz - 20KHz) inter-channel (max) inter-channel (typ) intra-channel (max) intra-channel (typ) Frequency Response 20Hz - 20KHz (max) 20Hz - 20KHz (typ) <0. 009% THD+N <0. 009% THD+N >75dB >90dB >85dB >100dB +/- 0. 5dB +/- 0. 2dB Audio Converters Mute Delay 24 bit, 48KHz (output) infinite attenuation Standard CobraNet Latency Low Latency 3. 646 milliseconds Network to BASIS CobraNet input through full DSP chain to analog output 6. 313 milliseconds Program Outputs Connector Type Cable Type Available "stock" Lengths Maximum Qualified Length Control Room Foldback Monitoring Connector Type Pinout Tap points 8 4 HD-15 dataport connections QSC DataPort cable, QSC p-n DPC-x ("x" designates cable length in feet) 1, 2, 3, 4, 5, 6, 10, and 20 ft. , custom lengths available. "Euro Style") detachable terminal blocks 1:+(input) 2:-(input) 3:CHASSIS GND 4:-(output) 5:+(output) 8 internal input, 8 internal output, 8 amplifier (pre-, post-, amplifier) software selectable Monitor Input Monitor Signal (unit off) Maximum level Impedance (nominal) CMRR, 20Hz-20KHz Unity gain connection, relay bypass +21 dBu 10K ohms >54 dB Specifications are subject to change without notice. 20Hz-20KHz Distortion (20Hz-20KHz) Noise Floor Output Impedance (nom) Output Load (min) Monitor Level Control Range (nom) Relay Outputs Connector Type Configuration Pinout Switching Capacity (nom) Logic Outputs Connector Type Configuration Pinout Omni Inputs Connector Type Configuration Pinout Normal Operating Range Potentiometer Operation Voltage Tolerance Current Output RS-232 Port QSControl CobraNet Indicators QSControl Status CobraNet Status Power Diagnostic DataPort Status (Port) LCD Data Display Sum of Monitor Input and signal from internal monitor tap point(s) +/- 0. 5dB <0. 05% @ +4dBu >90dB 100 Ohms 600 Ohms 0dB to -95. 5dB in 0. 5dB steps 2 discrete floating relay switch outputs 3-pin "Phoenix Style" (a. k. a. [. . . ]