User manual REMINGTON 105 CTI

[. . . ] Owner's Instruction Book for: Model 105 CTi Autoloading Shotguns Manual IMPORTANT! READ ALL INSTRUCTIONS AND WARNINGS IN THIS BOOK BEFORE USING THE FIREARM. Some Illustrations May Depict Cosmetic Differences page 2 . . . . . . . . the ten commandments of firearm safety page 7 . . . . . . . . important parts of the firearm page 10 . . . . . . how to load and unload page 13 . . . . . . lubrication and maintenance page 20 . . . . . . how to obtain parts and service A Tradition of Performance and Safety. In 1816 Eliphalet Remington was confident he could make a flintlock that was as good or better than any he could buy. The barrel he handcrafted set a new standard for firearm accuracy and spawned generations of products that have made Remington® Arms America's leading gunmaker. While performance and style are certainly hallmarks of Remington firearms, one factor ultimately drives their performance. Eliphalet Remington never lost sight of the fact that his rifles were potentially Eliphalet Remington's first lethal and could kill someone if handled improperly. [. . . ] Push the rod all the way through the barrel until the rod can be seen at the chamber opening. If an object cannot be easily pushed out of the barrel with a cleaning rod, return the firearm to the factory or a REMINGTON® AUTHORIZED SERVICE CENTER. The Trigger Assembly Pulling the trigger FIRES the firearm. The trigger assembly of the Model 105 CTiTM shotgun has been set at the Remington factory for optimal trigger pull. The factory settings provide a crisp, clean trigger pull for superior performance. All repairs to the trigger assembly must be made by the factory or a REMINGTON® AUTHORIZED SERVICE CENTER. WARNING: Never place your finger on the trigger unless you are ready to fire the firearm. The Barrel WARNING: The inside of the barrel must be clean and free of obstructions. Engage the safety by placing the safety mechanism in the "ON" or "SAFE" position. Look into the ejection port, visually check the chamber, loading port and magazine to make sure the shotgun is completely unloaded. Push the rod completely through the barrel until the rod can be seen at the ejection and loading port. How To Assemble The Model 105 CTiTM is shipped with the barrel removed. See "Cleaning Lubrication And Maintenance Instructions" on page 13. Engage the safety by placing the safety mechanism in the "ON" or "SAFE" position. Visually check the barrel making sure there are no obstructions. PICTURE 9 Cardboard Packing Ring Fore-End Barrel Magazine Cap Magazine Plug Choke Tubes Choke Tube Wrench 9 4. WARNING: When the fore-end is removed, keep your hands away from the action spring when moving the bolt to the open position. Insert the barrel into the receiver and the gas cylinder over the magazine tube. See Picture 10. PICTURE 10 Barrel AMMUNITION: The 12 gauge Model 105 CTITM is designed to function optimally with ammunition ranging from 2 3/4", 2 3/4 dram 1 1/8 oz. loads WITH A PUBLISHED muzzle velocity less than 1290 FPS may not create enough energy to fully cycle the firearm. SHOTGUN SHELL Gauge Marking Head Body Load Marking Primer Rim TO LOAD THE CHAMBER AND MAGAZINE: NOTE: The bore should be cleaned before loading the firearm the first time. Engage the safety by placing the safety mechanism in the "ON" or "SAFE" position. With the bolt locked open, look into the ejection port and visually check the chamber, loading port and magazine making sure the shotgun is completely unloaded. Place one shell of the correct gauge and length into the magazine until your thumb passes the carrier. The shell will be immediately loaded into the chamber automaticaly. Magazine Tube & Action Spring 8. Once the barrel bottoms out in the receiver, slowly release the operating handle. Open the bolt, by pulling the operating handle fully rearward. How To Load And Unload To Load The Firearm WARNING: The specific gauge and length of shotshell ammunition suitable for use in your shotgun is marked on the barrel. [. . . ] · Method of payment: Mastercard, Visa, Amex or Discover card number and expiration date. Owner's manuals/instruction books may be requested via our web site at: www. remington. com or by calling 1-800-243-9700. To locate the Remington Authorized Service Center nearest you visit our web site at www. remington. com and use our Repair Service Locator. If you need additional on-line assistance, e-mail us at info@remington. com to obtain a listing of Authorized Service Centers. [. . . ]