User manual ROLLEI PREGO 140

[. . . ] If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: Reorient or relocate the receiving antenna. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Use of shielded cable is required to comply with Class B limits in Subpart B of Part 15 of the FCC rules. Do not make any changes or modifications to the equipment unless otherwise specified in the manual. [. . . ] · Digital zoom cannot be used in the movie mode. 19 Using the self-timer The self-timer duration is 10 seconds. After the activation of the self-timer by pressing the shutter button, the self-timer lamp starts blinking slowly for 7 seconds and then blinking faster for the rest of 3 seconds. This allows you to get into the scene when taking group images. E 1. Open the lens cover, turn mode dial to the mode, and power on the camera. To cancel self-timer photography at any time, press the shutter button to disrupt the sequence. NOTE · After one shot is taken, the self-timer mode is turned to off. 20 Using the macro mode Use the macro mode to shoot a close-up of the subject, such as flowers or insects. Open the lens cover, turn the mode dial to the mode, and power on the camera. side of the camera to the The icon appears on the LCD monitor and status LCD. Press the shutter button. To disable macro photography, slide the focus switch back to normal. E NOTE · When shooting a close-up in macro mode, use the image LCD monitor to compose your shot, avoiding the off-center parallax phenomenon. · There is not a distinct point (subject range) at which normal mode is favored over macro mode; take in image an both optical modes and compare the results. · After a macro shot is taken DO NOT FORGET to reset the lens to the normal position. Using the flash The flash is designed to function automatically when lighting conditions warrant the use of flash. You can take an image using a flash mode suitable to your circumstances. To return to the regular display from 4X-enlarged status, press the OK button twice. Current position of enlargement Entire image E 4X NOTE · Pressing the OK button magnifies the image from 1X2X4X. · Pressing the OK button reduces the image from 4X2X1X. 25 Displaying thumbnail images This function allows you to view nine thumbnail images on the LCD monitor simultaneously so you may search for a particular image. E 1. Nine thumbnail images appear on the LCD monitor (assuming there are nine or more images in memory). To view a full-size image, press the OK button after selecting it by using the / button. NOTE · By pressing the button repeatedly, the image will show as follows. Image only Image and OSD (on-screen display) Thumbnail image display Slideshow display The slideshow function enables you to playback your images back automatically in sequential order as a slide show. This is a very useful and entertaining feature for reviewing recorded images and for presentations. 1. Set the playback interval by using the / button and then press the OK button. The slideshow star ts, displaying your images on the LCD monitor, one by one, at the set interval. To stop the slideshow display, press the OK / // button. NOTE · You can adjust the slideshow display interval within the range of 2 sec. For interval setting, refer to SLIDE SHOW in the Playback menu. 26 Deleting images You can delete one image/video clip by pressing the To delete one image at a time: 1. button. E NOTE · To delete the images or video clips stored in the internal memory, remember not to insert the memory card in the camera. [. . . ] Press the shutter button to toggle the DPOF print tag setting for the specified image. NOTE · When using the shutter button to enable the DPOF setting, the default setting is size=standard, and quantity=1. EXIT This option exits the record menu and then returns to the mode. You can also press the button again to exit. 40 Movie menu To adjust movie menu setting, press the the option you wish to set by using the / button in the button. mode and navigate to LCD BRIGHTNESS This option adjusts the brightness of the LCD monitor. Refer to LCD BRIGHTNESS in Record menu for detailed information. E EXIT This option exits the movie menu and then returns to the mode. [. . . ]