User manual SABINE FBX1020 PLUS

[. . . ] OPERATING GUIDE QUICK-START OPERATION DECLARATION OF CONFORMITY ABOUT THE FBX-1020PLUS V2 6 1 2 3 FBX-1020PLUS OPERATING INSTRUCTIONS FREQUENCY RESPONSE WORLD'S BEST FEEDBACK CONTROLLER WHO NEEDS FBX?ACTIVE/BYPASS SWITCH SIGNAL LEVEL DUAL-FUNCTION RESET SET TOTAL NUMBER OF FILTERS SET FIXED A/C POWER INPUT AUDIO INPUTS & OUTPUTS FBX-1020PLUS CONTROLS 3 3 3 3 3 4 4 4 4 4 4 4 4 LOCK FIXED FILTERS FIFTH OCTAVE FILTER STAGE ACTIVITY POWER SWITCH FUSE APPLICATION DIAGRAMS 4 4 4 4 4 5 WHERE THE FBX FITS IN YOUR SOUND SYSTEM A NOTE ABOUT GRAPHIC EQUALIZERS UNDERSTANDING FIXED & DYNAMIC FILTERS CLIPGUARDTM ADAPTIVE CLIP LEVEL CONTROL CLIPGUARDTM TURBO MODE GUIDE FBX SETUP FOR SINGLE INSERT POINT FBX SETUP FOR INSERT SEND & RETURN HOW TO OPERATE THE FBX-1020PLUS HOW TO USE THE FBX-1020PLUS FEATURES USING THE LOCK FIXED FEATURE SELECTING FILTER WIDTH IMPORTANT OPERATING CONSIDERATIONS MEMORY BYPASS MODE RESETTING THE FILTERS TURBO MODE SETUP DEFEATING TURBO MODE MOBILE VS. STATIONARY MICROPHONES FREQUENTLY ASKED QUESTIONS INDEX FBX-1020PLUS ENGINEERING SPECIFICATIONS CAUTIONS & WARNINGS LIMITED WARRANTY 6 6 6 6 6 7 7 7 8 8 8 8 8 8 8 8 8 8 9 9 10 11 12 FBX SETUP FOR MONITORS FBX SETUP FOR ENTIRE MIX 5 5 QUICK-START OPERATION For best results, read all operating instructions before using the FBX-1020Plus. If you're already familiar with the FBX or just want a basic overview of FBX operation, this simple quick-start procedure is for you. [. . . ] Remember: if you leave LOCK FIXED on, the fixed filters won't initialize. The LED indicating LOCK FIXED should be off when initializing. You can mix 1/10- and 1/5-octave filters in the same channel. If you have an especially bad feedback problem, try making the first few filters 1/5-octave and the remaining filters 1/10-octave. 7 How To Use The FBX-1020Plus Features Using the LOCK FIXED feature In very few situations the FBX may mistake music for feedback and drive the fixed filters deeper than necessary, such as in a church with a pipe organ, or during a performance with a great deal of intentional sustained electric guitar feedback. You can prevent the fixed filters from deepening beyond their preset depth by pressing the LOCK FIXED button on the front panel after setup. The LOCK FIXED LED will light to indicate that the FBX is in LOCK FIXED mode. The fixed filters stay locked until you press the LOCK FIXED button again. TURBO Mode Setup The FBX-1020Plus incorporates TURBO mode setup, which is indicated by a flashing red "CLIP" LED. This lightning-quick setup feature cuts the time for FBX filter initialization to just a few seconds, and it reduces the volume level of the feedback during setup. The 1020Plus is set in TURBO mode at the factory and automatically engages every time you press RESET (resetting filters). The 1020Plus automatically returns to normal program mode when the first dynamic filter is set or when you press the front panel LOCK FIXED button. ALL FILTER LEDS WILL CYCLE TO INDICATE THE FBX IS ABOUT TO EXIT TURBO MODE. WARNING: TURBO Mode will cause distortion in your audio program -- it is for setup only. You must follow the setup procedure outlined in the previous section, and do not play program during TURBO setup mode. (Clip level is set to the lowest level so the feedback clips quickly; therefore, your program will also be clipped in TURBO mode. Be sure a dynamic filter is set, and if one isn't, press the LOCK FIXED button before your program begins. ) You'll know the 1020Plus is in TURBO mode if the red CLIP LED flashes when no other signal level LEDs are lit. Selecting filter width If you're using the FBX for a music application, the standard 1/ 10-octave Constant Q filter is usually preferable. However, in spoken word applications, such as lectures or teleconferencing, we recommend using the wider 1/5-octave filter for more robust feedback control. You may enable the 1/5-octave filters by pressing the "FIFTH OCTAVE" button, and the built-in LED will light. Press the button again to set subsequent filters to standard 1/10-octave filters. You can mix filter widths in the same channel (see "IMPORTANT TIP" below). Important Operating Considerations Memory The FBX stores the positions and depths of the filters in nonvolatile internal memory when the unit is turned off or during a power failure. The unit will return all filters to their previous frequencies and depths when it is turned back on. Defeating Turbo Mode You can manually override TURBO mode if necessary: Press LOCK FIXED (the LOCK FIXED light will turn on), then press it again. (LOCK FIXED light will go out). Bypass Mode The FBX has a true power-off bypass. The signal is unaffected in BYPASS MODE even if the unit is turned off. Please note that if a combination of BALANCED and UNBALANCED inputs and outputs is used, the signal may be disconnected in BYPASS MODE. Mobile vs. [. . . ] In the event of a defect in material and/or workmanship covered by this limited warranty, Sabine will repair the defect in material or workmanship or replace the product, at Sabine's option; and provided, however, that, in any case, all costs of shipping, if necessary, are paid by you, the purchaser. THE WARRANTY REGISTRATION CARD (or ONLINE REGISTRATION FORM) SHOULD BE ACCURATELY COMPLETED, MAILED TO AND RECEIVED BY SABINE WITHIN FOURTEEN (14) DAYS FROM THE DATE OF YOUR PURCHASE . Bring the defective item to any Authorized SABINE DEALER and present therewith the ORIGINAL PROOF OF PURCHASE supplied to you by the AUTHORIZED SABINE DEALER in connection with your purchase from him of this product. If the DEALER is unable to provide the necessary warranty service, you will be directed to the nearest other SABINE AUTHORIZED DEALER which can provide such service. [. . . ]