User manual SABINE PHANTOM MIC RIDER PMR-HH1

[. . . ] · This Operating Guide 4 Features Your new Sabine Phantom Mic RiderTM is the first phantom-powered DSP unit that provides these five powerful features: · FBX Feedback Exterminator Increases gain before feedback. · Automatic Gain Control Helps maintain level as you move toward and away from the mic. · Proximity Effect Control Reduces the excess bass sound as you get closer to the mic - maintains flat frequency response at all distances from the mic. · Plosive Control Reduces the loud pops and bursts from certain consonant sounds in speech. · Infrared Gate Mutes the mic when no one is in front of it using the included infrared sensor. 5 Installing the PhantomTM Above the table or podium GP 1. Mute the audio channel for the microphone you have selected to use with the Phantom. Plug the Phantom (PMR-GP1) into the same base connector as the mic, as shown in Figure 1. The Phantom requires phantom power - when you plug in the Phantom you should see the LED turn green indicating phantom power is present. [. . . ] Press the SEN button again and you can cycle through the three settings: Setting #1 (Low), #2 (Medium), and #3 (High). When you arrive at your desired setting simply wait and that setting will become active when the LED stops flashing and turns to green. You can verify your setting by repeating Step 2. 15 Operating the PhantomTM FBX Setup GP+HH This procedure will set the FBX Feedback Exterminator filters and will increase your gain before feedback. These FBX filters are all fixed filters - once Ready Mode is engaged they are fixed in their location, width, and depth. They are no longer adaptive, and there are no dynamic filters available with the Phantom. These are not necessary because your podium mic should not be moving during the program!The Phantom will provide between two and four FBX filters depending on system acoustics. Make sure the Phantom is installed as described in "Installing the Phantom" previously. Turn down the gain for this mic and mute all other mics on your mixer. Using the Phantom Tool press and hold the FBX button for three seconds. The amber LED will flash continuously when you have held it long enough. Slowly raise the gain for this mic until you hear the first feedback tone. You will hear a pulsing sound moments before the feedback filters are set - this helps indicate the FBX 16 GP+HH Operating the PhantomTM FBX Setup (continued) is in setup mode. Continue raising gain until the amber LED turns green and the pulsing stops. There will be a momentary muting of the mic at the end of Setup mode - this is normal. You can manually exit Setup Mode at any time by pressing the FBX button once during the Setup procedure. It will give you more gain before feedback for this microphone and increase the distance you can stand from the mic and still be heard. 17 Operating the Phantom TM Proximity & Plosive Control Setup GP+HH 1. Make sure the Phantom is installed as described in "Installing the Phantom" previously. Using the Phantom Tool, press the PROX button momentarily and you will see the red LED flash. Factory default setting is Setting #2, indicated by two quick flashes. Press the PROX button again and you can cycle through the three threshold settings: Setting #1, Setting #2, and Setting #3. When you arrive at your desired setting simply wait and that setting will become active when the LED stops flashing. [. . . ] UNDER NO CIRCUMSTANCES WILL SABINE BE LIABLE FOR ANY LOST PROFITS, LOST SAVINGS, ANY INCIDENTAL DAMAGES OR ANY CONSEQUENTIAL DAMAGES ARISING OUT OF THE USE OR INABILITY TO USE THE PRODUCT, EVEN IF SABINE HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. THESE LIMITED WARRANTIES ARE IN LIEU OF ANY AND ALL WARRANTIES, EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR USE; PROVIDED, HOWEVER, THAT IF THE OTHER TERMS AND CONDITIONS NECESSARY TO THE EXISTENCE OF THE EXPRESS LIMITED WARRANTIES, AS HEREINABOVE STATED, HAVE BEEN COMPLIED WITH, IMPLIED WARRANTIES ARE NOT DISCLAIMED DURING THE APPLICABLE ONE-YEAR PERIOD FROM DATE OF PURCHASE OF THIS PRODUCT. SOME STATES DO NOT ALLOW LIMITATION ON HOW LONG AN IMPLIED WARRANTY LASTS, OR THE EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES, SO THE ABOVE LIMITATIONS OR EXCLUSIONS MAY NOT APPLY TO YOU. THESE LIMITED WARRANTIES GIVE YOU SPECIFIC LEGAL RIGHTS, AND YOU MAY ALSO HAVE OTHER RIGHTS WHICH MAY VARY FROM STATE TO STATE. [. . . ]