User manual SABINE SW70-T BELTPACK TRANSMITTER QUICK SETUP GUIDE

[. . . ] SW70-T Beltpack Transmitter Quick Setup Guide SIDE A 1 1 PLEASE CAREFULLY READ THE OPERATING GUIDE FOR COMPLETE INSTRUCTIONS. Select the INPUT to Match your Input Type INSTRUMENT MICROPHONE OR SELECT 2 Select GUI or MIC: Use the UP or DOWN buttons to select your desired input (GUI or MIC). [. . . ] Conversely, setting a more extreme PAD level (-40, -37, or -34 dB) may require you to raise your system gain unnecessarily, resulting in a noisier output. Watch the input meter on either the transmitter or the receiver (see illustrations) and set your level so there are at least three indicators illuminated for normal program level, with an occasional move to the fourth indicator. If you see clipping, choose a lower pad setting (for example, from -10 to -14 dB). Changing PAD Settings Clipping Zone 1 SELECT 2 3 Select PAD function: Use the transmitter's SELECT button to scroll through functions until PAD flashes in the transmitter LCD. Suggested PAD Settings Venue Select PAD setting: Use the UP or DOWN buttons to select the desired setting. Selection is stored after 3 seconds. Check for Clipping: Check to see if the receiver's Audio Level Meter stays out of the Clipping Zone. Microphones low-output Microphones standard Acoustic instruments low-gain pickups Electric guitars low-gain pickups Microphones higher gain Electric guitars standard Instruments high-gain preamps PAD -10 dB -14 dB -20 dB -26 or -30 -34 dB 3 1 Set Low Cut Filter to Match your Sound Toggles between no filter and 12 dB/octave low frequency roll-off filter (starting at 75 Hz). 2 SELECT OR USER TIP: ELECTRIC GUITARS AND BASSES ARE PROBABLY BEST AT 0, SOME ACOUSTIC INSTRUMENTS MAY BENEFIT FROM 75. Select LOW CUT function: Push the transmitter's SELECT button to scroll through functions until L O or L 75 appears on the transmitter LCD. Select LOW CUT setting: Use the UP or DOWN buttons to toggle between no filter (indicated in the display as L 0) or low roll-off (indicated by L 75). Selection is stored after 3 seconds. 4 1 © 2004 Sabine, Inc. Battery RUN TIME Hours Resets the display that indicates the length of power-on time (hours and minutes) since the last battery change or recharge. 2 SELECT NOTE: RUN-TIME HOURS ARE RESET AUTOMATICALLY WHEN CHARGING BATTERIES. To view Run-time Hours: Use the transmitter's SELECT button to scroll through functions until TIME appears in the LCD. To Reset Run-time hours: Simultaneously press and hold both the UP and DOWN arrows until LCD resets to 0. 00. LIT-SW70T-QG-EN-040319. pmd SW70-T Beltpack Transmitter Quick Setup Guide Opening Access Compartment SIDE B 1 Battery door handle 2 Press down firmly with both thumbs on battery door handle (above Sabine logo) and slide away from LCD. Lift bottom edge of door slightly and continue pulling door down away from LCD until the door opens fully (90-degree angle from transmitter body). Closing Access Compartment 1 Swing door down, flush with transmitter body. 2 With both thumbs pressing firmly on door handle (above Sabine logo), slide door up toward LCD until door lip catches under main body of transmitter, and bottom of door is flush with bottom of transmitter body. Important Battery Information Your Sabine 2. 4 GHz beltpack transmitter (SW70-T) comes with two size AA rechargeable NiMH batteries. For best results, charge the battery for at least 8 hours before using it for the first time. [. . . ] MUST BE RECYCLED OR DISPOSED OF PROPERLY. PLEASE CAREFULLY READ THE OPERATING GUIDE FOR COMPLETE INSTRUCTIONS. © 2004 Sabine, Inc. SABINE ® 13301 NW US Highway 441 · Alachua, FL 32615-8544 USA · +USA (386) 418-2000 · +USA (386) 418-2001 fax Sabine@Sabine. com · www. Sabine. com [. . . ]