User manual SABINE SW75-T BELTPACK TRANSMITTER QUICK SETUP GUIDE

[. . . ] SW75-T Beltpack Transmitter Quick Setup Guide SIDE A 1 1 PLEASE CAREFULLY READ THE OPERATING GUIDE FOR COMPLETE INSTRUCTIONS. Select the INPUT to Match your Input Type MICROPHONE INSTRUMENT 2 SELECT DOWN UP Select INPUT function: Push the transmitter's SELECT button to scroll through functions until the word INPUT appears at bottom in the transmitter LCD, which stays backlit while you are editing all parameters. Select INSTR or MIC: Use the UP or DOWN buttons to select your desired input (Instrument or Microphone). [. . . ] If you see clipping, choose a lower pad setting (for example, go from -10 to -14 dB). Changing PAD Settings Clipping Zone 1 SELECT 2 DOWN UP 3 Select PAD function: Press the SELECT button to scroll through functions until PAD flashes in the transmitter LCD. Select PAD setting: Use the UP or DOWN buttons to select the desired setting. Selection is stored after 3 seconds. Check for Clipping: Make sure the receiver's Audio Level Meter stays out of the Clipping Zone. Suggested PAD Settings - adjust for your application Sabine SWT31L-TA4 Cardioid Lav SWT73W-TA4 SWT56W-TA4 Cardioid Headworns Electric guitars low-gain pickups Microphones higher gain SWTVT50-TA4 Omni Lav SVT70LW-TA4 SVT40L-TA4 SVT70BW-TA4 Omni Lav Omni SVT80BW-TA4 Headworns SVT81LW-TA4 Cardioid Headworns Electric guitars standard Instruments high-gain preamps PAD General Microphones low-output Microphones standard Acoustic instruments low-gain pickups -10 dB -17 dB -23 dB -26 to -34 dB -37 dB 3 1 Set Low-Cut Filter to Match your Sound Toggles between no filter and 12 dB/octave low frequency roll-off filter (starting at 75 Hz). 2 SELECT DOWN UP USER TIP: FOR ELECTRIC GUITARS & BASSES USE L0; SOME ACOUSTIC INSTRUMENTS MAY BENEFIT FROM L75. Select LOW CUT function: Push the transmitter's SELECT button to scroll through functions until L 0 or L 75 appears on the transmitter LCD. Select LOW CUT setting: Use the UP or DOWN buttons to toggle between no filter (indicated in the display as L 0) or a roll-off at 75 Hz (indicated by L 75). 4 1 © 2007 Sabine, Inc. Battery RUN TIME Hours Resets the display that indicates the length of power-on time (hours and minutes) since the last battery change or recharge. 2 DOWN UP To view Run-time Hours: Use the transmitter's SELECT button to scroll through functions until TIME appears in the LCD. To Reset Run-time hours: Simultaneously press and hold both the UP and DOWN arrows until LCD resets to 0. 00. NOTE: RUN-TIME HOURS ARE RESET AUTOMATICALLY WHEN CHARGING BATTERIES. LIT-SW75T-QG-EN-070223. pmd SW75-T Beltpack Transmitter Quick Setup Guide Opening Access Compartment SIDE B 1 2 Gently pull the door open. Using your thumb and forefinger, grab both tabs and simultaneously pull down toward the bottom of the beltpack. Closing Access Compartment Swing the door back up and close it by firmly pushing the top part of the door in until you hear the locks click. Important Battery Information Your Sabine 2. 4 GHz beltpack transmitter (SW75-T) comes with two size AA rechargeable NiMH batteries. For best results, charge the battery for at least 8 hours before using it for the first time. Please note that the full charging potential of the battery will be achieved after the first 5 charging cycles have been completed. [. . . ] MUST BE RECYCLED OR DISPOSED OF PROPERLY. PLEASE CAREFULLY READ THE OPERATING GUIDE FOR COMPLETE INSTRUCTIONS. © 2007 Sabine, Inc. SABINE ® 13301 NW US Highway 441 · Alachua, FL 32615-8544 USA · +USA (386) 418-2000 · +USA (386) 418-2001 fax Sabine@Sabine. com · www. Sabine. com [. . . ]