User manual SAMSUNG SRF924DLS

[. . . ] Refrigerator user manual English This manual is made with 100 % recycled paper. imagine the possibilities Thank you for purchasing a Samsung product. To receive a more complete service, please register your product at www. samsung. com/register Free Standing Appliance DA68-02836K (EN)-01. indd 1 13. 10:21 safety information SAFETY INFORMATION • Before operating the appliance, please read this manual thoroughly and retain it for your reference. • Use this appliance only for its intended purpose as described in this instruction manual. [. . . ] Insert one Snap Ring only, Inserting two or more Snap Rings may cause the Snap Rings to slip out or make a rubbing noise. • Lift up the lower door and insert the Snap Ring into the space between the Door and the Hinge. • Keep the Snap Rings out of the reach of children and make sure that children do not play with them or put them into their mouths. • Two 1 mm, 1. 5 mm, 2 mm, and 2. 5 mm Snap Rings come with the Refrigerator. • If the Refrigerator is level before you load it with food, the Refrigerator may become unbalanced due to the weight of the food. • If you raise the door too far, it can rub against the Top Cover. • If the Refrigerator is not level back and front, put a solid panel (such as a plastic panel, a plastic ruler, etc. ) on the floor where the rear legs will rest, and then fix it in place with plastic tape. When you push in the Refrigerator, make sure the rear legs rest on the panel. • If you have a wooden floor or similar soft floor, take care not to damage the floor when pushing the Refrigerator into place. CAUTION Snap Rings included with the refrigerator: 1 mm 1. 5 mm 2 mm 2. 5 mm 20_ setting up DA68-02836K (EN)-01. indd 20 13. 10:21 HOW TO ADJUST THE DOOR GAP If the gap between the left and right fridge compartment doors is not even. • You can adjust the gap by turning the bolt at the top right of the cold storage compartment door. You can break it. • Water line installation kits are available at extra cost from your dealer. We recommend using a water line installation kit that contains copper tubing and 6mm (¼”) compression nut. Connecting to the water supply line 1. First, shut off the main water supply. 01 1. With the doors closed, remove the 3 screws holding the top cover using a Phillips screwdriver, and then lift it off together with the connected cables. 2. Locate the nearest cold water drinking line and install the pipe clamp and shut off valve. Cold water line Pipe clamp setting up Shut off valve 2. Turn the bolt with a 4 mm hexagonal L-wrench to adjust the gap. Turn the bolt counter clockwise ( the gap. 3. Connect the water line installation kit to the shut off valve. Cold water line Water line installation kit ) to narrow Pipe clamp Shut off valve INSTALLING THE WATER DISPENSER LINE A water dispenser with a filter is one of the helpful features on your new refrigerator. To help promote better health, the water filter removes unwanted particles from your water. For the ice maker to operate properly, water pressure of 138 ~ 862 kPa is required. If the refrigerator is installed in an area with low water pressure (below 20 psi), you can install a booster pump to compensate for the low pressure. After you have connected the water line, make sure the water storage tank inside the refrigerator is properly filled. To do this, press the water dispenser lever until the water runs from the water outlet. Connecting the water supply line to the refrigerator. There are several items that you need to purchase to complete this connection. You may find these items sold as a kit at your local hardware store. For Copper Tubing For Plastic Tubing • ¼” copper tubing • ¼” plastic tubing • ¼” compression nut (1pc) → Molded end(Bulb) • Ferrule (2pc) • ¼” compression nut (1pc) setting up _21 DA68-02836K (EN)-01. indd 21 13. 10:21 cut off 1/4“ of the plastic tubing to make sure you get a snug, leak-free connection. Under normal conditions, the water dispenser can fill a 170 cc cup in about 10 seconds. Plastic Tubing (Assembled) Compression Fitting (Assembled) Molded end(Bulb) Compression nut (B) (1/4”) (Not supplied) Copper tubing or (Not supplied) Refrigerator Compression Nut (1/4”) (Assembled) Ferrule (Not supplied) Plastic tubing (B) (Not supplied) Household water supply line 1. Connect the household water line to the assembled compression fitting. -- If you are using copper tubing, slip the compression nut ( B ) (not supplied) and ferrule (not supplied) on the copper tubing (not supplied) as shown. [. . . ] Is the back of the refrigerator too close to the wall, preventing proper ventilation?T ry moving the back of the refrigerator at least 2 inches from the wall. It is normal and occurs because various accessories are contracting or expanding in response to temperature changes in the refrigerator interior. • If it sounds as if something is hitting something else inside the refrigerator, this is normal. [. . . ]