User manual SHURE PGXD WIRELESS QUICK START GUIDE REV 2

[. . . ] PGXD Wireless System Shure PGXD Wireless PGXD sans fil de Shure Shure PGXD Sem Fio ©2010 Shure Incorporated 27B14513 (Rev. 2) Printed in U. S. A. D D D D D D D D PGXD PGX Digital Wireless Systems Offering uniquely tailored wireless solutions for vocalists, guitarists, and presenters, PGX-Digital combines the trusted legacy of Shure wired microphones with state-of-the-art, 24-bit digital wireless technology to deliver strong, clean RF performance. [. . . ] · When the LED flashes red, the batteries must be replaced to power on the transmitter. PGXD Adjusting Gain For best audio quality, set transmitter gain so the audio LED on the receiver flickers green and amber during the performance. For best results, monitor the LED from directly in front. Bodypack Transmitter The bodypack has 26 dB of audio gain adjustment. · Increase gain (clockwise +) for microphones · Decrease gain (counterclockwise ­) for guitars or high-output instruments Handheld Transmitter Access the gain switch by unscrewing the head of the microphone. · ­10dB: Use only if audio is distorted due to high vocal levels. BIAS AUDIO 0dB -10dB PGXD AUDIO 0dB -10dB 3 Single System Setup Scan Use the scan feature on the receiver to find a clear channel. Synchronize Synchronize the transmitter to the receiver by aligning the infrared (IR) ports and pressing the sync button. After a successful sync, the transmitter LED momentarily flashes red and the receiver ready light illuminates. LED screen displays current channel channel press channel button to scan for a clear channel system scans for the channel with the least interference NOTE: This wireless system may be affected by RF interference when used in proximity to other wireless devices such as cordless phones, baby monitors, and two-way radios. For best results, use the scan and sync feature before each use or if you experience problems. Multiple System Setup Use the following steps to ensure the best performance when installing multiple wireless systems at the same location. Note: Turn on any other digital equipment that could cause interference during the performance so it will be detected during the frequency scans in the following steps. Make sure the group number is the same for all receivers (see Manual Group Selection). · Important: After syncing each transmitter, leave it on so that scans from the other receivers will not select that channel. Compatible Frequencies · Be sure only one transmitter IR port is exposed when synchronizing each system. When operating multiple systems simultaneously, choose one group from the following table and set all systems to different channels within that group. Number of Systems 2 3 4 5 Group (by band) X8 3 to 9 3 to 9 3 to 9 7 to 9 X8A (Austrailia) 3 to 9 3 to 9 --- X8B (Brazil) 3 to 9 3 to 9 3 to 9 -- 4 Manual Channel and Group Selection (receiver only) Using the receiver to scan for a channel is the best way to find the best frequency for your system. However, for multiple system setup, you may need to manually set the group number. At the desired channel or group number, wait for the flashing to stop. Transfer the new frequency setting to the transmitter using the automatic sync function. channel group display channel display channel select 3s channel select 6s channel channel channel channel channel channel channel Locking and Unlocking Controls Locking the system controls prevents accidental muting or channel adjustment during performances. Transmitter To lock the controls: With the transmitter off, hold the power button down until the green LED flashes (~5 seconds) To unlock the controls: With the transmitter on, hold the power button down until the green LED flashes (~5 seconds) To lock the channel: Hold the channel button until the numbers flash (~10 seconds) To unlock the channel: Hold the channel button until the numbers flash (~5 seconds) Receiver 5 Troubleshooting Issue No sound or faint sound Indicator Status Receiver ready LED on Receiver ready LED off Solution Verify all sound system connections · Turn on transmitter · Make sure the batteries are installed correctly · Perform automatic transmitter setup · Insert fresh batteries Receiver LED screen off Transmitter indicator LED flashing red LED screen shows dash and value Transmitter LED flashes red for 7 seconds after attempting to sync Noise bursts or audio dropouts N/A Make sure AC adapter is securely plugged into electrical outlet Replace transmitter batteries. [. . . ] 28, 22/F, 625 King's Road King's Road King's Road Wannenäckestr. 28, Shure 22/F, 625 Shure Incorporated Incorporated Incorporated Shure 22/F, 625 74078 Heilbronn, Germany 5800 West 5800 West Touhy Avenue Touhy Avenue Touhy Avenue74078 Heilbronn, Germany 74078 Heilbronn, Germany Point, Island East Island East 5800 West North North Point, North Point, Island East Hong Kong Niles, IL 60714-4608 USA Hong Kong Hong Kong Niles, IL 60714-4608 USA Niles, IL 60714-4608 USA Phone: 49-7131-72140 Phone: 49-7131-72140 Phone: 49-7131-72140 Phone: Phone: 847-600-2000 847-600-2000 847-600-2000 Phone: Phone: 852-2893-4290 Phone: 852-2893-4290 Phone: 852-2893-4290 Fax: 49-7131-721414 Fax: 49-7131-721414 Fax: 49-7131-721414 Fax: 847-600-1212 (USA) Fax: 847-600-1212 (USA) Fax: 847-600-1212 (USA) Fax: 852-2893-4055 Fax: 852-2893-4055 Fax: 852-2893-4055 Email: Email: info@shure. de info@shure. de info@shure. de Email: Fax: Fax: 847-600-6446 847-600-6446 847-600-6446 Fax: Email: info@shure. com. hk Email: info@shure. com. hk Email: info@shure. com. hk Email: info@shure. com Email: info@shure. com Email: info@shure. com www. shure. com ww. shure. com www. shure. com©2010 Shure Incorporated Incorporated Incorporated ©2010 Shure ©2010 Shure [. . . ]