User manual SIMA SSW-L6 EX

[. . . ] 3 Front Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Rear Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Typical Hook up. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] · Can handle up to 100 watts amplifier power. · · · Front Panel Figure 1, Front Panel (SSW-L6 EX shown) Controls 1. Volume control ­ An 11-step volume control for each speaker pair. Rear Panel Figure 2, Rear Panel (SSW-L6 EX shown) 4. Amplifier Connections ­ connect the speaker output of your receiver or amplifier (100 watts max). Amplifier B optional Note: Be sure to align the pins on the terminals with the removable connector blocks correctly. Do not shift over 1 pin. Typical Hook up Figure 3, Overview of typical system hook-up. (SSW-L6 EX shown) Installation Tips · · · · · It is recommended to use 18 or 16 AWG gauge stranded wire. Since speakers have different efficiencies, more efficient speakers will sound louder than less efficient speakers. Either select your speakers to have the same efficiencies (a typical measurement is 90 db/watt) or add a speaker volume control between the SSW-L4/L6 EX and the speaker in the room where the speaker is located. Most places require that you use special in-wall speaker wire with a specific "CL" fire rating. Keep the speaker wiring from running close to AC power wiring for safety and to avoid any noise pick up. Installation Make sure your receiver or power amplifier is turned off before doing any wiring · To make a connection, using a wire stripper, strip 3/8" of insulation from the end of the wire. To avoid short circuits and possible amplifier damage, do not strip too much insulation from the wire. · Tightly twist the end of the wire so that there are no frayed wires. · For wiring convenience, connectors unplug from the connector block. · Insert wire and tighten the terminal screw using a small screwdriver. Connect the wires from the speaker output from your receiver or amplifier to the SSW-L4 or L6 EX terminals marked AMPLIFIER. Pay attention and connect the "+" output from the right front output on the amplifier to the right "+" input on the SSW-L4 or L6 EX and connect the "-" output from your amplifier to the "-" input on the SSW-L4 or L6 EX. Likewise, connect the left channel wires to the left input of the SSW-L4 or L6 EX · Next, connect the wires from each of the speakers to the corresponding connection on the SSW-L4 /L6 EX. · If you are using a second amplifier, connect it to the AMP B terminal. [. . . ] Sima's liability for damages in no event shall exceed the amount paid for this product. Sima neither assumes nor authorizes anyone to assume for it any other liabilities. Some states do not allow the exclusion or limitation of incidental or consequential damages, so the above limitation or exclusion may not apply to you. [. . . ]