User manual SMEG 110B91GMCX

[. . . ] Contents 1 Instructions 1. 1 1. 2 1. 3 1. 4 1. 5 1. 6 1. 7 2. 1 2. 2 2. 3 2. 4 2. 5 How to read the user manual This user manual Appliance purpose General safety instructions Manufacturer liability Identification plate Disposal General description Cooking hob Control panel Other parts Available accessories Instructions First use Using the accessories Using the hob Using the storage compartment Using the oven Cooking advice Programmer clock Instructions Cleaning the appliance Removing the door Cleaning the door glazing Cleaning the inside of the oven Extraordinary maintenance Gas connection Adaptation to different types of gas Electrical connection Positioning 38 38 38 38 38 39 39 39 2 Description 40 40 41 41 42 43 3 Use 3. 1 3. 2 3. 3 3. 4 3. 5 3. 6 3. 7 3. 8 4. 1 4. 2 4. 3 4. 4 4. 5 4. 6 5. 1 5. 2 5. 3 5. 4 45 45 46 46 48 49 49 51 53 4 Cleaning and maintenance 57 57 57 58 59 59 60 5 Installation 61 61 64 68 69 We advise you to read this manual carefully, which contains all the instructions for maintaining the appliance's aesthetic and functional qualities. For further information on the product: www. smeg. com 37 EN Instructions 1 Instructions 1. 1 How to read the user manual This user manual uses the following reading conventions: Instructions General information on this user manual, on safety and final disposal. Use Information on the use of the appliance and its accessories, cooking advice. Cleaning and maintenance Information for proper cleaning and maintenance of the appliance. [. . . ] Advice for defrosting and proving • Place frozen foods without their packaging in a lidless container on the first shelf of the oven. • To defrost meat, use the rack placed on the second level and a tray on the first level. In this way, the liquid from the defrosting food drains away from the food. • For successful proving, a container of water should be placed in the bottom of the oven. To save energy • Stop cooking a few minutes before the time normally used. Cooking will continue for the remaining minutes with the heat which has accumulated inside the oven. • Reduce any opening of the door to a minimum to avoid heat dispersal. • Keep the inside of the appliance clean at all times. 52 Use 3. 8 Programmer clock Setting the time If the time is not set, the oven will not switch on. On the first use, or after a power failure, the digits will be flashing on the appliance's display. 1 Minute minder timer key 2 Cooking duration key 3 End of cooking key 4 Value decrease key 5 Value increase key Please make sure the programmer clock shows the cooking duration symbol , otherwise the oven will not switch on. The symbol on the display indicates that the appliance is ready to start cooking. Timed cooking Timed cooking is the function which allows a cooking operation to be started and then ended after a specific length of time set by the user. The display will shows the digits and the symbol displayed between the hours and the minutes. 5 seconds without pressing any key in order for the function to activate. On the display, symbol turns off, symbol flashes and the buzzer sounds. To reset the set program, press keys and at the same time and switch off the oven manually. Programmed cooking Programmed cooking is the function which allows a cooking operation to be started at a set time and then ended after a specific length of time set by the user. Set the cooking time as described in the previous point “Timed cooking”. The sum of the current time plus the pre-set cooking duration will appear on the display. 5 seconds without pressing any key in order for the function to activate. On the display, symbol turns off, symbol flashes and the buzzer sounds. To display the end of cooking time, press the key. 54 Use Minute minder timer The minute minder timer does not stop the cooking operation but rather informs the user when the set time has run out. [. . . ] Adjusting the minimum setting for LPG Tighten the screw located at the side of the tap rod clockwise all the way. Following adjustment to a gas other than the one originally set in the factory, replace the gas setting label on the appliance with the one corresponding to the new gas. Lubricating the gas taps Over time the gas taps may become difficult to turn and get blocked. Lubrication of the gas taps should be performed by a specialised technician. 65 EN Installation Gas types and Countries Gas types 1 Natural Gas G20 G20 20 mbar G20/25 20/25 mbar 2 Natural Gas G25 G25 25 mbar 3 Natural Gas G25 G25 20 mbar 4 LPG G30/31 G30/31 28/37 mbar G30/31 30/37 mbar G30/31 30/30 mbar 5 LPG G30/31 G30/31 50 mbar 6 City Gas G110 G110 8 mbar 7 City Gas G120 G120 8 mbar IT GB-IE FR-BE DE AT NL ES PT SE RU DK • • • • • • • • • • • • • • • • • • • • • • • • • • • 66 Installation Burner and nozzle characteristics tables 1 Natural Gas G20 Rated heating capacity (kW) Nozzle diameter (1/100 mm) Pre-chamber (printed on nozzle) Reduced capacity (W) 2 Natural Gas G25 Rated heating capacity (kW) Nozzle diameter (1/100 mm) Pre-chamber (printed on nozzle) Reduced capacity (W) 3 Natural Gas G25 Rated heating capacity (kW) Nozzle diameter (1/100 mm) Pre-chamber (printed on nozzle) Reduced capacity (W) 4 LPG G30/31 Rated heating capacity (kW) Nozzle diameter (1/100 mm) Reduced capacity (W) Rated capacity G30 (g/h) Rated capacity G31 (g/h) 5 LPG G30/31 Rated heating capacity (kW) Nozzle diameter (1/100 mm) Pre-chamber (printed on nozzle) Reduced capacity (W) Rated capacity G30 (g/h) Rated capacity G31 (g/h) 6 City Gas G110 Rated heating capacity (kW) Nozzle diameter (1/100 mm) Pre-chamber (printed on nozzle) Reduced capacity (W) 7 City Gas G120 Rated heating capacity (kW) Nozzle diameter (1/100 mm) Pre-chamber (printed on nozzle) Reduced capacity (W) AUX 1. 0 72 (X) 400 AUX 1. 0 72 (F1) 400 AUX 1. 0 77 (F1) 400 AUX 1. 0 50 400 76 75 AUX 1. 0 43 (H2) 400 76 75 AUX 1. 0 145 (8) 400 AUX 1. 0 135 (8) 400 SR 1. 8 97 (Z) 500 SR 1. 8 94 (Y) 500 SR 1. 8 100 (Y) 500 SR 1. 8 65 500 131 129 SR 1. 8 58 (M) 500 131 129 SR 1. 8 185 (2) 500 SR 1. 8 175 (1) 500 R 3. 0 115 (Y) 800 R 3. 0 121 (F2) 800 R 3. 0 134 (F3) 800 R 3. 0 85 800 218 214 R 2. 9 70 (Y) 800 211 207 R 3. 0 260 (3) 800 R 3. 0 240 (3) 800 UR2 4. 2 75 + 135 (H1)+(H3) 1900 UR2 4. 2 75 + 145 (H1)+(H3) 1900 UR2 4. 1 80 + 145 (Y)+(H3) 1900 UR2 4. 2 46 + 91 1900 305 300 UR2 4. 2 43 + 70 (S1)+(H2) 1900 305 300 UR2 3. 8 140 + 320 1400 UR2 3. 9 130 + 290 1400 The nozzles not provided are available at Authorised Service Centres. [. . . ]