User manual SMEG A1-5

[. . . ] INSTRUCTIONS FOR SAFE AND PROPER USE_______________ 36 INSTALLATION OF THE APPLIANCE________________________ 38 ADAPTATION TO DIFFERENT TYPES OF GAS _______________ 40 FINAL OPERATIONS _____________________________________ 42 DESCRIPTION OF CONTROLS ____________________________ 44 USE OF THE COOKING HOB ______________________________ 51 USE OF THE OVEN ______________________________________ 53 AVAILABLE ACCESSORIES _______________________________ 54 COOKING HINTS ________________________________________ 55 CLEANING AND MAINTENANCE ___________________________ 61 EXTRAORDINARY MAINTENANCE _________________________ 64 THESE INSTRUCTIONS ARE VALID ONLY FOR END USER COUNTRIES WHOSE IDENTIFICATION SYMBOLS APPEAR ON THE COVER OF THIS MANUAL. INSTRUCTIONS FOR THE INSTALLER: these are for the qualified technician who must carry out a suitable check of the gas system, install the appliance, set it functioning and carry out an inspection test. INSTRUCTIONS FOR THE USER: these contain user advice, description of the commands and the correct procedures for cleaning and maintenance of the appliance. 35 Introduction 1. INSTRUCTIONS FOR SAFE AND PROPER USE THIS MANUAL IS AN INTEGRAL PART OF THE APPLIANCE AND THEREFORE MUST BE KEPT IN ITS ENTIRETY AND IN AN ACCESSIBLE PLACE FOR THE WHOLE WORKING LIFE OF THE COOKER. WE ADVISE READING THIS MANUAL AND ALL THE INSTRUCTIONS THEREIN BEFORE USING THE COOKER. [. . . ] To set the cooking time, proceed as follows: Press the key for 1/2 seconds; the pointer will move to position 12 (Fig. Use the and keys to set the cooking time; 1 key is pressed, 1 minute will whenever the be added to the cooking time, and every 12 minutes a new inside segment will light up (figure 2 shows a cooking time of 1 hour). Once the required time has been set, cooking will start about 6 seconds after the last time the - - - or . Once cooking has started, the display will show the current time, represented by the constantly 2 on segments, and the minutes left until cooking finishes, represented by the flashing segments (every flashing segments indicates 12 minutes of cooking time left). When the end of the cooking time is reached, the timer will switch off the oven heating elements, the beeps will start and the numbers on the dial will flash. The cooking time can also be reset by deleting the program set; for 1 or 2 seconds will delete the time pressing the central key set and the oven will have to be switched off by hand. Caution: cooking times of more than 6 hours cannot be set. 49 Instructions for the user Cooking start: as well as setting a cooking duration time, the user can also set the cooking start time (up to 12 hours after the current time). Within 6/7 seconds after the last time the or keys are pressed, press the key to set the cooking start time. The display will show the current time with the inside segments indicating the cooking end time illuminated. 6/7 seconds after the last time a key is pressed, the display will show the current time and the cooking start and end times, indicated by the illuminated inside segments. The segments on the display will be constantly on until the current time is the same as the cooking start time; as soon as the current time reaches the cooking start time set, all the inside segments will start to flash, indicating that the oven has started cooking. When the end of the cooking time is reached, the timer will switch off the oven heating elements, the beeps will start and the numbers on the dial will flash. - - - To reset the entire program set, keep the central key pressed for 1 or 2 seconds: if cooking has already started the oven will have to be switched off by hand. The image on the right shows an example of programming: the current time is 7. 06 and cooking is programmed to start at 8 o'clock and finish at 9. At 8 o'clock, the inside segments between 8 and 9 will start to flash and the hour pointer will remain still. Caution: for the oven to start cooking after the programming procedure just described, the thermostat and function selector must be properly set on the temperature and function required 5. 3. 5 "DEMO" Function Models with analogue/digital programmer feature a "DEMO" function which deactivates the heating elements while leaving the other functions unchanged. To activate it, simply press the , , and keys and keep them held down for 3-4 seconds. A confirmation buzzer will inform the user that the function is active. When the "DEMO" function is active, the number 6 on the clock flashes at regular intervals. To deactivate it, simply repeat the same procedure. 50 Instructions for the user 6. USE OF THE COOKING HOB 6. 1 Lighting of the cooking hob burners Before lighting the hob burners check that the flame caps are in the correct position and that their burner caps are in place, making sure that the holes A in the flame caps correspond to the spark plugs and thermocouples. Grid B should be used with Chinese woks. Each knob corresponds to the burner indicated. To light the burners, press and turn the knob anticlockwise to the large flame symbol / . Keep the knob pressed for about 2 seconds to let the thermocouple heat up. [. . . ] If left to set for too long, they might damage the enamel lining of the oven. 10. 2 Cleaning of cooking hob components 10. 2. 1 Grids Extract the grids (the central one first, then the side ones). Clean with warm water and non-abrasive detergent, taking care to remove incrustation. Reassemble positioning the side ones first and then the central one. 61 Instructions for the user 10. 2. 2 Burner caps, flame cap crowns and burners To facilitate cleaning, caps, flame cap crowns, and burners are all removable. To remove the flame separating crown of the fish hob, loosen the two screws exposed after having removed the cap. [. . . ]