User manual SMEG CT29X

[. . . ] The manual is divided into sections giving you a step-by-step guide to all your appliance’s functions. The texts are easy to understand and are complete with detailed illustrations. This user-friendly manual will provide answers to all your questions about use of the dishwasher. Before using this dishwasher, carefully read chapter 2 “Use and safety warnings” of the attached general manual. [. . . ] Nomenclature of figures and tables: The progressive number of each figure is shown in the bottom righthand corner of the relative box. 4-01”, where the first number (4) indicates the section to which the figure belongs, while the second number (01) indicates the progressive number of the figure in section 4 (Fig. The tables are numbered in the same way, bearing in mind that “Tab. ” is used instead of “Fig. ” (e. g. : Tab. If a table occupies more than one page, a letter is added after the progressive number (e. g. : “Tab. 4-01b”). EN Rev 0. 0 3 EN INTRODUCTION Symbols used in this manual (see tab. This symbol highlights information and warnings which, if not observed, may compromise personal safety or damage the appliance. This symbol highlights general information and warnings. 1-01 4 Rev 0. 0 USER INSTRUCTIONS 2 2. 1 DESCRIPTION AND USE OF THE CONTROLS Upper panel EN All the dishwasher controls are grouped on the upper panel (see fig. The dishwasher can only be switched on, programmed, switched off, etc. 2-01) of the various controls on the upper panel is given below. 2 end 3 4 1 Fig. Program indicator lights These show which program is selected and whether there are any faults (troubleshooting). Program selection button Press in sequence to select the required program. When the door closes, the program will start from where it was interrupted. This operation should be performed only if necessary as it could cause irregular program performance. EN 2. 2. 5 Changing the current program To change the current program, simply open the door of the dishwasher and select the new program. Close the door to run the new program automatically. 2. 2. 6 Canceling the current program • To cancel the current program, open the door and press and hold down the program selection button (ref. 2-02) for a few seconds until the indicator lights of the fourth and fifth programs turn on (ref. • After about 1 minute, the dishwasher terminates the cycle and the indicator lights of the fourth and fifth programs (ref. 2-03 Rev 0. 0 9 EN 2. 2. 7 Switching off USER INSTRUCTIONS At the end of the program, the dishwasher emits a short beep and the indicator lights of the fourth and fifth program (ref. Turn off the appliance by opening the door and pressing the on/off button (ref. 2-04 10 Rev 0. 0 USER INSTRUCTIONS 3 • • • • • EN ENERGY SAVING AND ENVIRONMENTAL RESPECT Always try to run the dishwasher fully loaded. If available, connect the dishwasher to a hot water system with a temperature of up to 60°C (140°F). • When possible, skip the drying cycle by opening the door after washing: the air and the residue heat will dry the dishes to perfection. 3. 1 Reducing the consumption of detergent and respecting the environment The phosphates contained in dishwasher detergents are harmful to the environment. To avoid using excessive amounts of detergent and to save on electricity: • Separate the more delicate items from those that are more resistant to aggressive detergents and high temperatures; • Do not pour the detergent directly onto the dishes. Rev 0. 0 11 EN 4 USER INSTRUCTIONS REMOVING THE DISHES At the end of the washing program, wait at least 20 minute before removing the dishes in order to allow them to cool. [. . . ] To prevent any water droplets on the upper rack from falling onto the dishes in the lower rack, empty the lower rack first and then the upper one. 12 Rev 0. 0 USER INSTRUCTIONS 5 TROUBLESHOOTING EN The dishwasher can to signal a number of malfunctions by turning on various indicator lights, as described below (see following table): FAULT end DESCRIPTION Acquastop failure The anti-flooding system has tripped (only for models fitted with this feature). Contact the technical assistance service. E1 end E3 Water heating malfunction The water is not heated or is incorrectly heated. Repeat the washing program; if the problem persists, contact the technical assistance service. end E4 Water temperature monitoring malfunction Interrupt the current program. Switch off the dishwasher, switch it back on again, program a new cycle and press start. [. . . ]