User manual SMEG CX68M8-1

[. . . ] 39 DESCRIPTION OF FRONT PANEL CONTROLS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40 USING THE OVEN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49 ACCESSORIES AVAILABLE. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51 RECOMMENDED COOKING TABLES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] You can now set an additional cooking time by turning PT1, or return to display of the current time by pressing PT1 twice. Press PT2 once to end the cooking process and switch the oven to OFF status. The minute minder also function works with no function set. Warning: the minute minder function does not stop the cooking process. Modifying the data set Once the countdown has started, its duration can be changed while cooking is in progress. The symbol starts flashing and PT1 can be turned to change the set duration. A few seconds after the last change, the symbol will stop flashing, and the countdown will restart from the new value. To change the preset temperature, wait for the symbol to become steady and turn PT1 to the right or left to increase or decrease the cooking temperature. Turning PT1 to the right increases the time, allowing the cooking start time required to be set. A few seconds after the required duration is set, the and symbols will stop flashing, and the oven will start to wait for the starting time set. At the end, the word STOP will appear on DSP1, cooking will stop and a buzzer will sound; press PT1 once to deactivate it. The oven will restart normal operation with the cooking settings selected previously. With the oven cold, remove the circular cover from the bottom of the oven (fig. 2). 1) 2) Press PT2 to switch the oven on, then use PT2 again to select the function. The display will show the recommended temperature for cooking pizza (280°C), (for the 2300W low energy consumption mode the recommended cooking temperature is 260°C). Preheat with these settings until the symbol (on DSP3) remains constantly on, then place the pizza on the special plate. It does not normally take more than 3-4 minutes to cook a pizza to perfection, although this time may vary depending on the dough used or individual taste. 8. 1 · Precautions for using the pizza plate Never use the pizza plate except as described above (for example, never use it on gas or ceramic hobs, or on ovens not designed to take this accessory). The pizza plate may be left in place while conventional cooking operations are in progress. Never use any oven function if the pizza plate or cover is not in position. If you like oil on your pizza, it is best to add it after removal from the oven since oil stains on the pizza plate are unsightly and may reduce its efficiency. · · · · 49 Instructions for the User 8. 2 To save energy The pizza stone acts as a heat reservoir. This allows energy consumption to be reduced, especially in cooking operations requiring medium-long times. In these cases, simply switch the oven off 10-12 minutes before the end of the cooking time. The heat gradually emitted by the refractory stone will ensure that the cooking temperature is maintained. 50 Instructions for the User 9. [. . . ] Before carrying out any operation involving access to live parts, disconnect the appliance from the electricity supply. 12. 1 Changing the light bulb Remove the protective cover A by unscrewing it anti-clockwise and replace the bulb B with another of the same type (25 W). Replace the protective cover A. Use only light bulbs approved for ovens (T 500°C). 61 Instructions for the Installer 12. 2 Removing the door 12. 2. 1 With type 1 mobile levers With the door completely open, lift the levers A of the two hinges until they touch the hinges B and take hold of the two sides of the door with both hands close to the 1) hinges. If the hinges have not locked, repeat the operation, raising the levers and keeping the door slightly raised. To reassemble, fit the hinges B into their grooves, then lower the door into place, ensuring that it remains fitted into the grooves C, then lower the levers A. [. . . ]