User manual SMEG DF613PX

[. . . ] INSTRUCTION MANUAL GUIDE FOR USING THE DISHWASHER AND THE WASHING PROGRAMS Contents 1. 5. Safety and operating instructions __________________________ 2 Installation and hook-up _________________________________ 7 Description of the controls ______________________________ 10 Operating instructions __________________________________ 22 Cleaning and maintenance ______________________________ 37 Troubleshooting ______________________________________ 41 Thank you for choosing one of our products. You are advised to read this manual carefully; it contains all the information you need about the right conditions for the proper, safe use of your dishwasher. The individual sections are laid out to provide you with a step-by-step guide to all your appliance's functions; the texts are easy to understand and are complete with detailed illustrations. [. . . ] If the option is not provided, we recommend the use of conventional products (separate detergent, salt and rinse aid), because with conventional washing cycles, combined products might create problems such as a white deposit, poor drying results and residues left on dishes. N. B. : When the salt and rinse aid containers are empty, the relative lights will remain on even if the “Flexi Tabs” option is selected. IMPORTANT: when no longer required, the option must be deactivated by pressing the relative button (the light goes out). If the water hardness has been set on a value above H3, and the “Flexi Tbas” option is activated, the relative light flashes, warning of a setting error. Multi-function products are not suitable for use with very "hard" water; this does not prevent the use of the option, but the washing results might not be of the best. ULTRA CLEAN The "ULTRA CLEAN" program prolongs the final hot rinse to ensure a further reduction in the bacteria level. If the temperature in the tank falls during this stage of the program (e. g. because the door is opened or due to a power blackout), the light of the option and the program lights (2) flash to warn that the additional washing phase has not been completed successfully. This does not mean that the wash program has been less effective than usual. 19 User instructions SPREAD HALF LOAD Suitable when there are not many dishes to be washed, it saves energy and reduces the program duration. Place dishes in both baskets then load the detergent dispenser than less than the normal amount for a full load. ENERSAVE OPTION This option further reduces energy consumption by opening the door at the end of the cycle for more effective drying. At the end of the wash an automatic device releases the door, which slowly opens by a few centimetres. This allows optimal drying even with low rinsing temperatures, for significant energy saving. Enersave is activated automatically if the selected program is compatible with the option. When the function is activated, opening of the door must not be impeded in any way; do not leave anything in the necessary space in front of the door to allow it to open. Do not force the door lock before the end of the cycle is signalled, as this would damage the mechanism. “CHILD LOCK” OPTION By pressing the indicated buttons (3) at the same time, the controls are locked, which is confirmed when the warning light on display turns on. This option stays active until the buttons (3) are pressed again. 20 User instructions TO SAVE ON ENERGY!… AND PROTECT THE ENVIRONMENT      Always try to run the dishwasher fully loaded. Use the washing program that is most appropriate for each type of load. If available, connect the dishwasher to a hot water supply up to 60°C. TO CUT DOWN ON DETERGENT CONSUMPTION!… AND PROTECT THE ENVIRONMENT The phosphates contained in dishwasher detergents are harmful to the environment. To avoid using excessive amounts of detergent and to save on electricity, observe the following:   separate the more delicate items from dishes that are more resistant to aggressive detergents and high temperatures; do not pour the detergent directly on the dishes. ENERGY MANAGEMENT At the end of the program, afterwards 5 minutes, the washing machine switches off automatically in order to reduce standby power consumption. In order to switch it on again, it is necessary to press the ON/OFF button. [. . . ] Wash them under running water and carefully replace them in their seats, checking that their rotary movement is in no way impeded. To remove the lower spray arm, simply lift it up, pulling by the central part. To remove the orbital spray arm assembly, take hold of the longer arm and pull the orbital unit upward. Wash the arms under a jet of running water and return them carefully to their seat. [. . . ]