User manual SMEG GKC955NLK

[. . . ] Contents 1 Instructions 1. 1 1. 2 1. 3 1. 4 1. 5 1. 6 1. 7 General safety instructions Manufacturer liability Appliance purpose Identification plate This user manual Disposal How to read the user manual 30 30 33 33 33 33 34 34 2 Description 2. 1 General Description 2. 2 Symbols 2. 3 Available accessories 35 35 36 36 3 Use 3. 1 3. 2 3. 3 3. 4 Instructions First use Using the accessories Using the hob 37 37 37 38 38 4 Cleaning and maintenance 4. 1 Instructions 4. 2 Cleaning the appliance 41 41 41 5 Installation 5. 1 5. 2 5. 3 5. 4 5. 5 5. 6 5. 7 Safety instructions Section cut from the countertop Mounting Fixing to the supporting structure Gas connection Adaptation to different types of gas Electrical connection 43 43 43 44 45 46 49 54 These instructions apply only for the destination countries listed on the appliance’s data plate. This is a class 3 built in hob. We advise you to read this manual carefully, which contains all the instructions for maintaining the appliance’s aesthetic and functional qualities. For further information on the product: www. smeg. com 29 EN Instructions 1 Instructions 1. 1 General safety instructions Risk of personal injury • During use the appliance and its accessible parts become very hot. • Never try to put out a fire or flames with water: Turn off the appliance and smother the flames with a fire blanket or other appropriate cover. [. . . ] • Make sure that the flame-spreader crowns are correctly positioned in their housings with their respective burner caps. • Cooking vessels or griddle plates should be placed inside the perimeter of the hob. • If any liquid does boil over or spill, remove the excess form the hob. 3. 2 First use 1. Remove any protective film from the outside or inside of the appliance, including accessories. Remove any labels (apart from the technical data plate) from accessories. Remove and wash all the appliance accessories (see 4 Cleaning and maintenance). 37 EN Use 3. 3 Using the accessories Ring reducers The ring reducers must be placed on the hob grids. In case of an accidental switching off, a safety device will be tripped, cutting off the gas supply, even if the gas cock is open. Return the knob to and wait at least 60 seconds before lighting it again. Correct positioning of the flame-spreader crowns and burner caps Before lighting the hob burners, make sure that the flame-spreader crowns are correctly positioned in their housings with their respective burner caps. Make sure that the holes in the burners are aligned with the igniters and thermocouples. Also ensure that the flame-spreader crowns are correctly engaged in the burner holes. 3. 4 Using the hob All the appliance’s control and monitoring devices are located together on the front panel. • leave a gap of at least 160 mm between the edge of the griddle and the side wall; • if one of the burners close to the wooden rear wall is an ultra-rapid burner, leave a gap of at least 160 mm between this wall and the edge of the griddle; • do not allow the burner flames to extend beyond the edge of the griddle; • Never use the griddle for more than 40 minutes. • When using aluminium griddles with Teflon non-stick coating, these should be pre-heated empty for a maximum of 5 minutes in order to avoid damage to the appliance and the coating. After preheating, place the foodstuffs on the griddle to cook them; do not exceed 40 minutes of total use for the griddle. 40 Cleaning and maintenance 4 Cleaning and maintenance 4. 1 Instructions Improper use Risk of damage to surfaces • Do not use steam jets to clean the appliance. • Do not use cleaning products containing chlorine, ammonia or bleach on parts made of steel or that have metallic surface finishes (e. g. • If it comes into contact with aggressive detergents, hard water or spills (cooking water, sauces, coffee, etc. ), clean immediately after having let the hob cool down. • Do not use rough or abrasive materials or sharp metal scrapers. • Do not wash removable parts such as the hob grids, flame-spreader crowns and burner caps in the dishwasher. 4. 2 Cleaning the appliance To keep the surfaces in good condition, they should be cleaned regularly after use. Ordinary daily cleaning Always use specific products only that do not contain abrasives or chlorine-based acids. Pour the product onto a damp cloth and wipe the surface, rinse thoroughly and dry with a soft cloth or a microfibre cloth. Food stains or residues Do not use steel sponges and sharp scrapers as they will damage the surface. Use normal, non-abrasive products and a wooden or plastic tool, if necessary. [. . . ] Unscrew the screws under each burner to remove the fixing plate. 2. Remove the knobs by lifting them from their housing. 49 EN Installation 5. Unscrew screw “A” and push air regulator “B” as far as it will go. Use a spanner to remove the nozzles “C” and install the new ones for the required gas supply, following the indications given in the relevant table (see “Burner and nozzle characteristics tables”). 50 Installation 3. [. . . ]