User manual SMEG LBA60EB

[. . . ] THE DISHWASHER IS INTENDED EXCLUSIVELY FOR PROFESSIONAL USE AND MUST BE USED BY COMPETENT PERSONNEL. IT IS DESIGNED TO WASH DISHES (PLATES, CUPS, BOWLS, BAKING PANS, SILVERWARE) AND SIMILAR ITEMS FROM THE GASTRONOMY AND THE COLLECTIVE RESTAURANT INDUSTRIES. IT CONFORMS TO THE INTERNATIONAL ELECTRIC AND MECHANICAL SAFETY NORMS (CEI-EN-IEC 60335-2-58/61770) AND ELECTROMAGNETIC COMPATIBILITY NORMS (CEI-IEC-EN 55014-1/-2, 61000-3;4, 50366). THE MANUFACTURER DECLINES ANY RESPONSABILITY FOR DAMAGE TO PERSONS OR THINGS CAUSED BY NON-OBSERVANCE OF THE INSTRUCTIONS PRESENT IN THE MANUAL, BY INCORRECT USE, BY TAMPERING EVEN WITH A SINGLE PART OF THE APPARATUS AND BY USE OF NONORIGINAL REPLACEMENT PARTS. [. . . ] REGENERATION ELECTROVALVE COLD RINSE ELECTROVALVE RINSE PUMP (MACHINE TYPE 4) WASH PUMP ( max. 0. 75 HP ) Optional OUTPUT POWER SUPPLIES, 230 VAC phase 6 KEYBOARD FUCNTIONALITY CW400RSD ­ CW400R MAIN FUNCTIONS WITH MACHINE POWERED ITEM L1 L2 Description Machine powered led indicator Tank emptying led indicator On/Off button Function This led indicator turns on (green) when electrical current is present This led indicator (green) indicates that the machine is emptying the Tank ­ the led flashes when the operation is in progress. Pressing this button with led indicator 1 on activates the keyboard and renders the machine operational. The last program used (wash cycles) will be shown on the 3 displays when turned on. To empty the Tank first remove the Tank's overflow, then press the button for 3 seconds. This inhibits water from being loaded and, after a Pressostat Tank-empty signal verifies that the Tank has been emptied, will only allow a limited amount of boiler water to circulate in order to facilitate the cleaning of the Tank. Tank emptying button At the end of the function the machine goes into a stand-by phase which is indicated by the appearance of three dashes "---" upon the displays. To render the machine operational again it is therefore necessary to insert the Tank's overflow and to press the button. If the machine is equipped with the drain pump option, the drain pump will also be activated. IN PARAMETERIZATION MODE, IF NO BUTTON IS PRESSED WITHIN 30 SECONDS THE KEYBOARD SHUTS DOWN AND RETURNS TO ITS OFF STATE. 8 Regeneration mode: Once having reached the set number of cycles, at the end of the last cycle (ex. The 20th or the 35th, etc. ) the message rig will appear flashing on the display for 10"; of it is desired to continue and the request is ignored, the message will appear for 10" at the end of every cycle. The pressing and afterwards press the regeneration cycle starts and moving dashes appear on the display; after 20 minutes the regeneration cycle ends and the machine goes into standby. Open the door, insert the overflow into the Tank and turn off the main wall switch. During the execution of the regeneration cycle it will not be possible to perform any operations. Refilling the supply of regenerating salt (for models equipped with water softeners) ). The refill is to be performed once the insufficient salt indicator appears on the display ( Perform the salt refill when there is no water in the Tank in order to keep wash water from entering the water softener device. After having extracted the basket, unscrew the cap and pour the salt through the provided funnel. Before screwing the cap back in place remove any eventual salt residues in proximity to the opening. 8. 5 Total drainage at the end of the day The dishwasher is capable of performing an auto-clean cycle at the end of the day. After having removed the overflow from the Tank, keep the button pressed for 3 seconds to initiate the emptying of the Tank and boiler. The boiler door must be closed while that of the Tank is to remain open. This will inhibit water from loading and, after the Pressostat's Tank empty signal is given, will only allow a limited amount of water from the boiler to circulate in order to facilitate the cleaning of the Tank. At the end of the function the machine goes into standby, indicated by the appearance of dashes "---" on the displays. [. . . ] Clean away the residues and rinse the filters abundantly before correctly reinserting them; Do not utilize pointy or sharp objects for cleaning. Be sure to remove eventual hardened calcium deposits in order to avoid their accumulation; Clean the surfaces well and frequently with a damp rag; use neutral, non-abrasive detergents which do not contain chlorine-based substances. In order to avoid drops or vapors damaging the steel surfaces, do not even use the above-indicated products for the cleaning of the flooring beneath or around the dishwasher. 10. 2 Periodic checks Disassemble the sprinklers (lower and upper 2-4) by removing the central screw (4); unscrew the caps at the two far ends of the rinsing sprinklers (7). Carefully reassemble the sprinklers. Clean the outside of the machine with neutral soap and a damp cloth. [. . . ]