User manual SMEG PGF95TG

[. . . ] • If the power supply cable is damaged, contact technical support immediately and they will replace it. Risk of damaging the appliance • Do not use abrasive or corrosive detergents on glass parts (e. g. • Never leave the appliance unattended during cooking operations where fats or oils could be released. • Do not use the appliance to heat rooms for any reason. 4 Instructions • The identification plate bears the technical data, serial number and brand name of the appliance. [. . . ] After lighting, keep the knob pressed in for a few seconds to allow the thermocouple to heat up. The burner may go out when the knob is released: In this case, the thermocouple has not heated up sufficiently. In case of an accidental switching off, a safety device will be tripped, cutting off the gas supply, even if the gas tap is open. Return the knob to and wait at least 60 seconds before lighting it again. Correct positioning of the grids Make sure that the grids are simply centred on their respective burners, without forcing the burners to be raised or tilted. If you find that a pan is particularly unstable, make sure that the grids have not been positioned incorrectly. Ring reducers The ring reducers must be rested on the hob grid. Make sure they are properly positioned. 10 Use For better burner efficiency and to minimise gas consumption, use pans with lids and of suitable size for the burner, so that flames do not reach up the sides of the pan. Once the contents come to the boil, turn down the flame far enough to ensure that the liquid does not boil over. Cookware diameters: • Auxiliary: 7 - 18 cm • Semi-rapid: 10 - 24 cm. • Ultra-rapid: 12 - 26 cm To prevent burns or damage to the hob or the counter top during cooking, all pans or griddles (not provided) must be placed inside the perimeter of the hob. Before lighting the hob burners, make sure that the flame-spreader crowns are correctly positioned in their housings with their respective burner caps. Make sure that the holes in the burners are aligned with the igniters and thermocouples. Also ensure that the flame-spreader crowns are correctly engaged in the burner holes. 11 EN IT Correct positioning of the flamespreader crowns and burner caps Practical tips for using the hob Cleaning and maintenance 4 Cleaning and maintenance 4. 1 Instructions Improper use Risk of damage to surfaces • Do not use steam jets to clean the appliance. • Do not use cleaning products containing chlorine, ammonia or bleach on steel parts or parts with metallic finishes on the surface (e. g. • Do not use abrasive or corrosive detergents on glass parts (e. g. • Do not use rough or abrasive materials or sharp metal scrapers. • Do not wash the removable components such as the hob grids, flame-spreader crowns and burner caps in a dishwasher. 4. 2 Cleaning the appliance To keep the surfaces in good condition, they should be cleaned regularly after use. Ordinary daily cleaning Always use only specific products that do not contain abrasives or chlorine-based acids. Pour the product onto a damp cloth and wipe the surface, rinse thoroughly and dry with a soft cloth or a microfibre cloth. Food stains or residues Do not use metallic sponges or sharp scrapers as they will damage the surfaces. Use ordinary non-abrasive products with the aid of wooden or plastic utensils if necessary. Do not allow residues of sugary foods (such as jam) to set inside the oven. If left to set for too long, they might damage the enamel lining of the oven. 12 Cleaning and maintenance Remove the grids and clean them with lukewarm water and non-abrasive detergent. [. . . ] General information Check the grid characteristics against the data indicated on the plate. The identification plate bearing the technical data, serial number and brand name is visibly positioned on the appliance. Perform the ground connection using a wire that is 20 mm longer than the other wires. The appliance can work in the following modes: • 220-240 V 1N~ 220-240V~ 1 mm2 20 mm Use a 3 x 0. 75 mm² three-core cable. [. . . ]