User manual SMEG PV175BD

[. . . ] BEFORE INSTALLATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . DESCRIPTION OF FRONT PANEL CONTROLS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ELECTRONIC PROGRAMMER (ON SOME MODELS ONLY) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37 7. 1 Setting the time . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] After the buzzer is stopped, the display will return to showing the current time together with the symbol, indicating that the oven is again ready for use in manual mode. 7. 6 Adjusting the buzzer volume The buzzer volume can be varied (3 settings) while it is in operation by pressing the key. 7. 7 Stopping the buzzer The buzzer stops automatically after seven minutes. To switch off the oven, return all the knobs to the 0 setting in sequence. 7. 8 Deleting the data set With the program set, keep the key of the function for deletion ( setting the value by pressing the value modification keys deletion of the duration as the end of cooking. The programmer will interpret 7. 9 Modifying the data set The cooking data set can be modified at any moment by keeping the key of the function for modification ( or ) pressed and at the same time pressing the value modification keys or . 38 Instructions for the User 8. ELECTRONIC ANALOGUE CLOCK (ON SOME MODELS ONLY) LIST OF BUTTON FUNCTIONS TIMER BUTTON END OF COOKING BUTTON CLOCK ADJUSTMENT AND RESET VALUE DECREASE BUTTON VALUE INCREASE BUTTON 8. 1 Setting the time When the oven is used for the first time, or after an interruption in the electricity supply, the display flashes at regular intervals. Press the key, keep it pressed, and at the same time use the value modification keys or to set the current time. The setting will be increased or decreased by one minute for each pressure. Keep both value modification keys pressed to change the numbers displayed more quickly. At the end of each programming operation 10 beeps will sound 3 times at intervals of about 1 minute. This sequence can be stopped at any time by pressing or . 8. 2 Minute-minder This function does not stop cooking; it simply activates the buzzer. Keep the key pressed and at the same time use or keys to set the minute minder. Each time a key is pressed, 1 outside segment, representing 1 minute of cooking time, will light up or go out. At the end of programmed cooking, manual operation of the oven has to be restored by holding down the key for a few seconds. Starting cooking: as well as setting a cooking duration, the cooking start time can also be set (with a maximum delay of 12 hours from the current time). To set the cooking start/end time, proceed as follows: - Set the cooking duration as described in the previous point. The current time appears on the display: use the and keys to set the cooking start time. - A few seconds after the last key is pressed, the cooking start time will appear on the display. - At the start of a programmed cooking operation, the dot between 12 and 1 will also illuminate, indicating that this is a programmed cooking procedure. After a few seconds, the cooking start time will return to the display. - At the end of the cooking time the timer will switch the oven heating elements off, the beeps will start to sound and the numbers on the dial will flash. - To reset the whole program set, keep the central key pressed for a few seconds: if cooking has already started, the oven will have to be switched off by hand. At the end of programmed cooking, manual operation of the oven has to be restored by holding down the key for a few seconds. Caution: for the oven to start cooking operations after the programming procedures just described, the thermostat and function selector knob must be correctly set on the temperature and function required. 8. 4 "DEMO" Function Models with analogue/digital programmer feature a "DEMO" function which deactivates the heating elements while leaving the other functions unchanged. [. . . ] If the hinges have not locked, repeat the operation, raising the levers A and keeping the door slightly raised. To reassemble, fit the hinges B into their grooves, then lower the door into place, ensuring that it remains fitted into the grooves C, then lower the levers A. 14. 2. 2 With mobile levers of type 2 Lift the levers B and take hold of the two sides of the door with both hands close to the hinges A. To reassemble, fit the hinges A into their grooves, then lower the door into place and engage the levers B. 1) 2) 14. 2. 3 Removing doors with pins Open the door completely and insert the pins (supplied) into the holes from the inside. [. . . ]