User manual SMEG S36

[. . . ] 37 BEFORE INSTALLATION. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38 USE OF THE OVEN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47 AVAILABLE ACCESSORIES. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49 CLEANING AND MAINTENANCE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] 7. 4. 2 Changing the preset temperature The temperature preset for each function can be changed to suit the user's requirements. At any time while cooking is in progress, turn PT1 in either direction to increase or decrease the cooking temperature by 5 degrees at a time. PT1 can also be held in the left or right position to increase or decrease the setting more quickly. 7. 5 Programmed cooking procedures 7. 5. 1 Cooking timed with the timer From ON status (see point "7. 2 Operating modes"), press PT1 once. The display will show the figures (constantly on) and the symbol (flashing). After a few seconds, the symbol will stop flashing and stay on constantly; the countdown will start from that moment. At this point it is also possible to select the cooking function required and wait for the buzzer to sound, indicating that the cooking time is over. You can now set an additional cooking time by turning PT1, or return to display of the current time by pressing PT1 twice. The minute minder also works with no function set. 41 Instructions for the user Warning. Modifying the data set Once the countdown has started it is possible to change its duration during cooking. The symbol starts flashing and PT1 can be turned to change the set duration. A few seconds after the last change, the symbol will stop flashing, and the countdown will restart from the new value. With the oven cold remove the circular cover from the bottom of the oven, leaving the pizza plate uncovered. Position the oven function knob on the symbol and the thermostat knob on 280°C. Pre-heat in this condition until the thermostat light switches off; then place the pizza onto the plate. For the best cooking results, it is normally not necessary to exceed the 3-4 minutes, although this time may vary according to the dough used or the tastes of the consumer. 8. 1 · Precautions for using the pizza plate Never use the pizza plate except as described above (for example, never use it on gas or ceramic hobs, or on ovens not designed to take this accessory). The pizza plate may be left in place while conventional cooking operations are in progress. Never use any oven function if the pizza plate or cover is not in position. If you like oil on your pizza, it is best to add it after removal from the oven since oil stains on the pizza plate are unsightly and may reduce its efficiency. · · · · 8. 2 To save energy The pizza stone acts as a heat reservoir. This feature makes it possible to reduce energy consumption, especially for cooking operations that require pre-heating or medium-long cooking times. In these cases, it is enough to reset the thermostat 10. 12 minutes before the end of cooking. The heat gradually emitted by the refractory stone will ensure that the cooking temperature is maintained. 47 Instructions for the user 9. AVAILABLE ACCESSORIES The oven features 4 support positions for plates and racks of different height. Grill: useful for holding cooking containers. [. . . ] To reassemble, fit the hinges into their grooves, then lower the door into place and extract the pins. 12. 3 Removing the door seal To permit thorough cleaning of the oven, the seal may be removed. Once the door has been taken off, lift the tabs at the corners as shown in the figure. 57 Instructions for the user 12. 4 Removing the glass panels The glass in the door should always be kept thoroughly clean. For easier cleaning, the door glazing can be fully removed by proceeding as described below. After opening the door and locking it in place as described in point "12. 2 Removing the door", remove the internal glass pane levering it as illustrated in figure 1, and detach the 4 pins that fix the glass to the door. [. . . ]