User manual SMEG SE2010MFX

[. . . ] The text is easy to understand and completed with pictures and some of the most commonly used pictograms. By reading this manual carefully, you will find all the answers to your oven operation queries. 28 Preliminary instructions 1. Preliminary instructions WE ADVISE YOU READ THIS INSTRUCTION MANUAL CAREFULLY BEFORE USING THE OVEN. THIS APPLIANCE HAS BEEN DESIGNED FOR THE FOLLOWING PURPOSES: - COOKING AND HEATING FOOD ANY OTHER USE IS TO BE CONSIDERED IMPROPER. [. . . ] 2. 2. 7 Minute-counter The programmer can also be used as a simple minute counter. IMPORTANT : THE USE OF THE MINUTE-COUNTER WILL NOT INTERRUPT OVEN OPERATION AT THE END OF THE SET TIME. By pressing key , the display shows ; keep the key pressed and or . By releasing the key , the at the same time press keys and appear on the programmed count starts and the symbols monitor. NOTE : AFTER PROGRAMMING THE MINUTE-COUNTER, THE DISPLAY WILL SHOW THE RIGHT TIME. WRONG SETTINGS ARE PREVENTED LOGICALLY (E. G. , ANY CONFLICT BETWEEN END OF COOKING TIME AND A LONGER TIME WILL NOT BE ACCEPTED BY THE PROGRAMMER). IMPORTANT : 2. 2. 8 Cancellation of set data Once the programme has been set, keep the key of the function to be cancelled pressed, while at the same time is reached by means of variation keys or . Time cancellation will be considered as endof-cooking time by the programmer. 2. 2. 9 Changing the set data The cooking data entered can be changed at any time by keeping the or . function key pressed and at the same time adjusting the keys 35 Description of controls 2. 3 CLOCK AND PROGRAMMER IMPORTANT : THE KNOB A MUST ALWAYS BE TURNED ANTICLOCKWISE. 2. 3. 1 Setting the clock To set the correct time, PRESS and turn knob A anticlockwise. NOTE : BEFORE SETTING THE PROGRAMMER ACTIVATE THE DESIRED FUNCTION AND TEMPERATURE. 2. 3. 2 Semiautomatic cooking Use this setting for automatic oven switch-off at the end of cooking time. Turn the knob A anticlockwise to set the cooking time in the window B. 2. 3. 3 Automatic cooking Use this setting to automatically start and stop the oven. Turn the knob A anticlockwise to set the cooking time in the window B. PULL and turn the knob A anticlockwise so the arrow C coincides with start of desired cooking time. 2. 3. 4 End of cooking When cooking is over, the oven will automatically switch off and, at the same time, an intermittent alarm will sound. 2. 3. 5 Switching off the alarm The alarm can be switched off manually by turning the knob A appears in window B. anticlockwise until symbol IMPORTANT : TO USE THE OVEN MANUALLY AFTER PROGRAMMING, TURN THE KNOB A APPEARS IN WINDOW B. Using the oven 3. 1 WARNINGS AND GENERAL ADVICE Before using the oven for the first time, pre-heat it to maximum temperature (280°C) long enough to burn any manufacturing oily residues which could give the food a bad taste. After a power failure, the display will flash at regular intervals showing . During cooking, do not cover the bottom of the oven with aluminium or tin foil and do not place pans or oven trays on it as this may damage the enamel coating. If you wish to use greaseproof paper, place it so that it will not interfere with the hot air circulation inside the oven. This considerably shortens cooking times and reduces power consumption, as well as giving better cooking results. 5. 1 TRADITIONAL COOKING FUNCTION SWITCH THERMOSTAT SELECTOR SWITCH - 50-280°C 50 - 280 °C This traditional cooking system where heat flows from both above and below is suitable for cooking food on one level only. The oven must be preheated until the preset temperature has been reached. Only place the food in the oven after the thermostat indicator light has gone out. Use high-rim pans to prevent fat splashing and dirtying the sides of the oven. 5. 2 HOT-AIR COOKING FUNCTION SWITCH THERMOSTAT SELECTOR SWITCH - 50-280°C 50 - 280 °C 40 Cooking hints This system is ideal for cooking different types of food (fish, meat, etc. , ) on more than one level without spreading of smell or taste. [. . . ] 7. 4. 4 Setting the cleaning cycle with the programmer clock FUNCTION SWITCH DURATION OF CLEANING CYCLE Position the function selector knob on symbol : the thermostat indicator light will come on. Turn the knob A anticlockwise to set duration of pyrolysis in window B. This can be set from a minimum of 1 hour 30' to a maximum of 3 hours. The cleaning cycle can be programmed so this begins at a preset time. Turn the knob A anticlockwise to set duration of pyrolysis in window B. [. . . ]