User manual SMEG SE2644ID1

[. . . ] SEPARATE THE VARIOUS WASTE MATERIALS AND TAKE THEM TO THE NEAREST SPECIAL GARBAGE COLLECTION CENTRE. THIS APPLIANCE IS MARKED ACCORDING TO THE EUROPEAN DIRECTIVE 2002/96/CE ON WASTE ELECTRICAL AND ELECTRONIC EQUIPMENT ­ (WEEE). THIS GUIDELINE IS THE FRAME OF A EUROPEAN-WIDE VALIDITY OF RETURN AND RECYCLING ON WASTE ELECTRICAL AND ELECTRONIC EQUIPMENT. DO NOT OBSTRUCT VENTILATION OPENINGS AND HEAT DISPERSAL SLITS. THE IDENTIFICATION PLATE, WITH TECHNICAL DATA, SERIAL NUMBER AND MARKING IS CLEARLY VISIBLE UNDER THE CASING. [. . . ] If the power symbol on the display starts to flash, it means that the pan you are using is not suitable for your appliance. The pans used for cooking must have a minimum diameter to guarantee proper functioning. Metal objects such as cutlery or lids must not be left on the hob as they risk being overheated without the user realising it. This printed circle indicates the minimum permissible diameter on that cooking zone. Pans with smaller diameters risk not being detected and therefore not activating the inductor. Pans that are larger than the cooking zones can also be used, but care must be taken that the bottom of the pan does not come into contact with other cooking zone and that it is always centred on the cooking zone perimeter. Use only recipients with a perfectly flat bottom and which are suitable for induction cooking or, if pans of this type are not available, recipients whose bottom is not crowned (concave or convex). Using a pan with an irregular bottom could jeopardise the efficiency of the heating system so that the pan is not detected on the hotplate. YES NO NO 22 Instructions for the user 5. 3 Switching on the cooking zone Press the button for the cooking zone you want to use (for example On the power display, 0 appears. you can set the power from 1 to 9. Once you have set the hotplate's power level, this will not be activated until a pan suitable for induction cooking is placed upon it. See paragraph 5. 2 Cookware" , the power level reaches 15. On the hotplates with keys If after having activating the hotplate, no power value is selected, the hotplate is automatically deactivated. Key Key , present only on some models, allow preset power levels for that hotplate to be : cooking level 7; : cooking level 11; Key : cooking level 15; 5. 3. 2 POWER button (only on some models) The key , present only on some models, permits supplementary power to be activated. to indicate that the POWER function is When it is pressed, the hotplate's power display will show active on that hotplate. 5. 3. 3 Switching off the hotplate Any hotplate can be switched off (the figure shows the front right-hand zone) at any time by pressing the ON/OFF key. The set power level will disappear from the display and if the hotplate remains hot even after it has been switched off, a begins to flash. On this regard, please refer to paragraph "5. 3. 5 Residual heat". 5. 3. 4 Automatic hotplate switch-off (on some models only) By means of this function, present on some models only, it is possible to program the switching off of the hotplate after a variable operating time: from 1 to 99 minutes. Select the desired power level at which to use the hotplate; and the cooking duration can be set. Using the keys At the end of the time the hotplate will be deactivated and a buzzer will sound temporarily. To interrupt the signal before time, press any button for the cooking plate used. 5. 3. 5 Residual heat Each cooking zone is equipped with a residual heat warning device. After any zone is switched off, a flashing " "may appear on the display. is flashing: in this case, proceed as described in paragraph "3". Cooking can be restarted while the 23 Instructions for the user 5. 3. 6 Cooking hob lock-out When the hob is on, it can be locked to avoid accidental modifications to the cooking values set. It is present only on the models that have the symbol . To activate the lock, with the hob on, press the keys simultaneously until the symbol appears on the display. [. . . ] Make sure there is a minimum of 750 mm between the hob and any shelf that may be installed directly above it. The dimensions indicated in the figure are the same for all models without a frame. The dimensions indicated in the figure are the same for all models with a frame. Below is supplied the table of comparison between the dimension Y to be created in the worktop and the dimension X of the cooker hob. DIMENSION X DIMENSION Y 300 600 700 900 270 565 565 878 Below is supplied the table of comparison between the dimension K to be created in the worktop and the dimension Z of the cooker hob. [. . . ]