User manual SMEG SE376MFX5

[. . . ] SHOULD THE APPLIANCE NOT FUNCTION, DISCONNECT IT FROM THE SUPPLY AND CALL THE NEAREST TECHNICAL ASSISTANCE CENTRE. NEVER ATTEMPT TO REPAIR THE APPLIANCE. 29 Introduction ALWAYS CHECK THAT THE CONTROL KNOBS ARE IN THE "ZERO" (OFF) POSITION WHEN YOU FINISH USING THE OVEN. NEVER PUT INFLAMMABLE OBJECTS IN THE OVEN: THEY COULD BE ACCIDENTALLY CATCH LIGHT AND CAUSE FIRES. DURING USE THE APPLIANCE BECOMES VERY HOT. TAKE CARE NOT TO TOUCH THE HEATING ELEMENTS INSIDE THE OVEN. THE I. D. PLATE WITH TECHNICAL DATA, REGISTRATION NUMBER AND BRAND NAME IS POSITIONED VISIBLY ON THE OVEN DOOR FRAME. [. . . ] To adjust heat intensity, turn the knob anticlockwise to the desired value. To return to heating inside the inner zone only, set knob first to 0 and then to any value between 2 and 12 as desired. 37 Instructions for the user Important (in models with flush controls only) To access to the control knobs simply press them and they will spring out into the operating position (fig. They must remain out in this position while the oven is in operation to prevent them from overheating. To return them to the retrected position, simply press down until the catch engages. To open the oven door, press the handle and it will spring out into the operating position (fig. It must remain in this position while the oven is in operation to prevent it from overheating. A B 38 Instructions for the user 3. 2 Electronic programmer LIST OF FUNCTIONS MINUTE-COUNTER KEY END-OF-COOKING KEY COOKING TIME KEY TIME BACK KEY TIME FORWARD KEY MANUAL OPERATION KEY 3. 2. 1 Clock adjustment When using the oven for the first time, or after a power failure, the display flashes regularly and indicates . By pressing keys or each single press changes the time by 1 minute either up or down. Before setting the programmer activate the desired function and temperature. 3. 2. 2 Semiautomatic cooking Use this setting for automatic oven switch-off at the end of cooking time. By pressing key , the display lights up, showing ; keep the key pressed and at the same time, press keys or to set the cooking time. 39 Instructions for the user to start the programmed cooking time count. The display Release key will now show the right time together with symbols A and . 3. 2. 3 Automatic cooking Use this setting to automatically start and stop the oven. ; keep the key By pressing key , the display lights up showing pressed and at the same time, press keys or to set the cooking time. By pressing key the sum of the right time + cooking time will appear; keep the key pressed and at the same time, press keys or to regulate the end of cooking time. Release key to start the programmed count and the display will show the right time together with symbols A and . After setting, to see how much cooking time is left, press key end of cooking time, press key . ; to see 3. 2. 4 End of cooking When cooking is over, the oven will automatically switch off and, at the same time, an intermittent alarm will sound. After switching off the alarm, the display will once again show the right time together with the symbol , indicating that the oven has returned to manual operation mode. 3. 2. 5 Adjusting alarm volume The acoustic alarm has three different settings. 3. 2. 6 Switching off the alarm The alarm switches off automatically after seven minutes. It can be manually turned off by pressing key . 40 Instructions for the user 3. 2. 7 Minute-counter The programmer can also be used as a simple minute counter. The use of the minute-counter will not interrupt oven operation at the end of the set time. By pressing key , the display shows ; keep the key pressed and at the same time press keys or . By releasing the key , the programmed count starts and the symbols and appear on the monitor. After programming the minute-counter, the display will show the right time. [. . . ] In case of tough spots, clean with a damp sponge using regular detergent. ADDITIONAL MAINTENANCE The oven may require additional maintenance or replacement of parts subject to wear such as seals, bulbs, and so on. The following instructions describe how to carry out these minor maintenance operations. Before any intervention, disconnect the power supply. 8. 1 Replacement of light bulb Remove the bulb protector A by turning anticlockwise and change bulb B (in the 8-function model with front glass panel change the halogen bulb C) with a similar one. [. . . ]