User manual SMEG SF372X

[. . . ] DO NOT LET UNSUPERVISED CHILDREN PLAY WITH THE HOB. REPLACED APPLIANCES MUST BE TAKEN TO A SPECIAL GARBAGE COLLECTION CENTRE. WHERE THIS APPLIANCE IS INSTALLED IN MARINE CRAFT OR IN CARAVANS, IT SHALL NOT BE USED AS A SPACE HEATER. DO NOT SPRAY AEROSOLS IN THE VICINITY OF THIS APPLIANCE WHILE IT IS IN OPERATION. The manufacturer declines all responsibility for damage to persons or things caused by non-observance of the above prescriptions or by interference with any part of the appliance or by the use of non-original spares. 5 Instructions for the installer 2. INSTALLATION OF THE APPLIANCE It is the law that all gas appliances are installed by an authorised persons. Clearance around the appliance must comply with the requirements of AS5601. (see 2. 6) 2. 1 The following operation requires building and/or carpentry work so must be carried out by a competent tradesman. [. . . ] Use only H05V2V2-F cable or similar which has a maximum temperature of 90°C. Any replacement needed should be carried out by a specialised technician who should make the mains connections according to the following diagram. L = brown N = blue = yellow-green The manufacturer will not be liable for any damage to persons or property caused by non-observance of the above instructions or deriving from the tampering of even a single part of the hob. 2. 4 Discharge of combustion products Discharge of combustion products must be guaranteed by means of hoods connected to a natural draught flue with certain efficiency, or by means of forced aspiration. An efficient aspiration system requires careful planning by a specialist capable of installing it, respecting the positions and distances prescribed by standards. After installation, the installer must issue a certificate of conformity. GAS CONNECTION This appliance is suitable for installation with Natural Gas or ULPG (propane). Refer to page 12 for the relevant burner pressure and appropriate injector sizes. When the appliance is to be connected to Natural Gas then the pressure regulator supplied must be fitted to the gas inlet. A test point (for checking the gas pressure) is supplied either with the regulator or as a separate fitting in the case of ULPG (propane) appliances. Connection of the appliance to the gas supply must be in accordance with the requirements of AS5601. A ½” BSP connector at the inlet is recommended and the gas supply line to the appliance must be of adequate length to allow sufficient withdrawal of appliance for service or disconnection and be: 1. In the case of functioning with other types of gas the burner nozzles must be changed and the minimum flame adjusted on the gas taps. To change the nozzles, proceed as described below. 4. 1 Replacement of nozzles on the hob This operation requires no primary air regulation. Extract the grids and remove all the caps and flame-spreader crowns; 2. replace the nozzles according to the type of gas to be used and the description in paragraph “3. 2 Burner and nozzle characteristics table”. Replace the burners in the correct position. 11 Instructions for the installer 4. 2 Burner Nominal gas consumption (MJ/h) 3. 9 6. 3 10. 8 13. 5 Burner and nozzle characteristics table LPG – 2. 75 kPa Injector (mm) 0. 54 0. 68 0. 88 1. 00 Auxiliary (1) Semi rapid (2) Rapid (3) WOK (4) Burner Nominal gas consumption (MJ/h) 3. 9 7. 5 12 15 NG – 1. 0 kPa Injector (mm) 0. 90 1. 20 1. 55 1. 75 Auxiliary (1) Semi rapid (2) Rapid (3) WOK (4) 4. 3 Arrangement of burners on cooking hob BURNERS 1 2 3 4 Auxiliary Semi rapid Rapid WOK 12 Instructions for the installer 5. FINAL OPERATIONS Having carried out the above adjustments, reassemble the appliance following, backwards, the instructions in paragraph “3. 2 Burner and nozzle characteristics table”. After adjustment to a different kind of gas from the one for which the cooker has been tested, replace the plate inside the heating compartment with one corresponding to the new kind of gas. This plate can be obtained from your nearest Authorised Assistance Centre. 5. 1 Adjustment of minimum for natural gas Light the burner and take it to the minimum. Remove the gas tap knob and turn the adjustment screw inside or at the side of the tap shaft (depending on the model) until there is a regular minimum flame. Replace the knob and check burner flame stability: (rapidly turning the knob from maximum to minimum position, the flame should not go out). Repeat the operation on all the gas taps. 5. 2 Regulation of minimum for LPG To regulate the minimum for LPG, completely tighten (clockwise) the screw inside or next to the gas tap pin (depending on the model). [. . . ] To light the burners, press and turn the knob anticlockwise to the large flame symbol. Wash them in warm water using a non-abrasive detergent, taking care to remove all tough spots. Re-install the caps on the corresponding crowns making sure that niches A are perfectly aligned with pins B of the burners. To work well, the ignition plugs and thermocouples must always be very clean. [. . . ]