User manual SONY AIR-SA15TI

[. . . ] 4-117-793-11(1) Wireless Audio System Operating Instructions AIR-SA20PK © 2008 Sony Corporation WARNING To reduce the risk of fire or electric shock, do not expose this apparatus to rain or moisture. To reduce the risk of fire, do not cover the ventilation opening of the apparatus with newspapers, tablecloths, curtains, etc. Do not place the naked flame sources such as lighted candles on the apparatus. To reduce the risk of fire or electric shock, do not expose this apparatus to dripping or splashing, and do not place objects filled with liquids, such as vases, on the apparatus. As the main plug is used to disconnect the unit from the mains, connect the unit to an easily accessible AC outlet. [. . . ] VOLUME +/. Start. playback. Operate the iPod to start playing the music. You can also operate the iPod using the remote (see "To control the iPod using the sub units"). To control the iPod using the main unit You can control your iPod with the following buttons on the remote. To Start playback Pause playback Select a menu or track for playback Skip a track Find a point in a track Press . Hold down / during playback, and release the button at the desired point. GB To use the main unit as a battery charger You can use the main unit as a battery charger for the iPod when the main unit is on. To stop charging the iPod, remove the iPod or turn off the main unit. Notes When placing or removing the iPod, handle the iPod in the same angle as that of the iPod connector on the main unit and do not twist or sway the iPod to prevent connector damage. When placing or removing the iPod, brace the main unit with one hand and take care not to press the controls of the iPod by mistake. Depending on the iPod model you are using and its status, operations using the main unit and the sub units may not be accepted or the wrong operations may be performed. Sony cannot accept responsibility in the event that data recorded to iPod is lost or damaged when using an iPod with this S-AIR product. Listening to the radio using the S-AIR connection Using the main unit Operations 1 Select. the. tuner. channel. When the S-AIR mode is set to "PARTY": Press PARTY CH on the remote repeatedly until "FM" or "AM" appears in the display. When the S-AIR mode is set to "MULTI SOURCE": The tuner channel is internally activated. Go to step 2. 2 3 Select. "FM". or. "AM. " Press BAND repeatedly. Perform. automatic. tuning. Press and hold TUNING +/ on the remote (or TUNING/SELECT +/ on the unit) until the frequency indication changes and then release. Scanning stops automatically when a station is tuned in, and then "TUNED" and "ST" (for FM stereo programs only) appear. Continued GB Using the sub units When a radio station is tuned on the main unit, you can listen to that station by following the steps below. To tune in a radio station using the sub units, that station needs to be preset beforehand (see "To call up a preset radio station using the sub units" (page 29)). Presetting radio stations You can preset your favorite radio stations and tune them in instantly by selecting the corresponding preset number. Use the main unit to preset the radio stations. 1 2 Select. the. tuner. channel. Press S-AIR CH repeatedly until "TUNER" appears in the display. 1 2 3 Tune. in. the. desired. station. See "Listening to the radio using the S-AIR connection" (page 27). Select. "FM". or. "AM. " Press and hold S-AIR CH until "FM" changes to "AM" or vice versa. Press. SYSTEM. MENU. on. the. unit. ENTER. on. the. unit. To tune in a station with a weak signal using the main unit If "TUNED" does not appear and the scanning does not stop, press TUNING +/ on the remote (or TUNING/ SELECT +/ on the unit) repeatedly to tune in the desired station. To reduce static noise on a weak FM stereo station using the main unit 1 Press. SYSTEM. MENU. on. the. unit. 2 Press. TUNING/SELECT. +/. on. the. unit. repeatedly. until. "FM. MODE". your. desired. preset. number. If another station is already assigned to the selected preset number, the station is replaced by the new stations. 3 Press. TUNING/SELECT. +/. on. the. unit. repeatedly. until. "MONO". There will be no stereo effect, but the reception will improve. GB 5 6 Press. ENTER. on. the. unit. The preset stations are retained for about half a day even if you disconnect the power supply cord or if a power failure occurs. Using an optional AV system You can enjoy audio and video of the connected iPod with an optional AV system. Operations 1 To call up a preset radio station using the main unit Press PRESET +/ repeatedly. To call up a preset radio station using the sub units 1 Preset. radio. stations. on. the. main. unit. (see. "Presetting. radio. stations". (page. Press S-AIR CH repeatedly until "TUNER" appears in the display. Press and hold S-AIR CH until "FM" changes to "AM" or vice versa. Connect. an. optional. AV. system. Start. playback. of. the. iPod. See "Listening to iPod music using the S-AIR connection" (page 25). 2 3 2 Select. the. tuner. channel. 3 Select. "FM". or. "AM. " Note The tuner's sound cannot be output through the iPod AUDIO OUT L/R jacks. [. . . ] RMT OFF* : The sub units are not accepting signals from the remote because the remote control function is set to "RMT OFF. " S-AIR* : Displayed from the point power of the sub unit is turned on until connection with the main unit is established. TIME NG* : The Daily Timer start and end times are set to the same time. UNLINKED* : The connection with the main unit is cut off. * Displayed on the sub units only. Precautions Notes on use of the S-AIR product As the S-AIR product transmits sound by radio waves, sound may skip when radio waves are obstructed. As the S-AIR product transmits sound by radio waves, equipment that generates electromagnetic energy, such as a microwave oven, may interfere with sound transmission. [. . . ]