User manual SONY ALT-SA31IR QUICK SETUP GUIDE

[. . . ] Graffiti, HotSync, and Palm OS are registered trademarks, and the HotSync logo and Palm are trademarks of Palm, Inc. Adobe and Adobe Acrobat Reader are trademarks of Adobe Systems Incorporated. All other trademarks are trademarks of their respective owners. CAUTION Please contact your nearest Sony dealer regarding the problem you are experiencing with your Sony product. 2 Table of contents What you can do with the CLIÉ Remote Commander . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] 5 Preparing the CLIÉ Remote Commander for your use . . . . . . . . . . . . . . . . . . . . . 6 Assigning devices to the CLIÉ Remote Commander . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Assigning operations to the application buttons and Jog Dial navigator . . . . . . . . . . . . . . 9 Using the CLIÉ handheld as a remote commander . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 Viewing the device name assigned to each quick-start button . . . . . . . . . . . . . . . . . . . . . . . . 12 CLIÉ Remote Commander menu items . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 Manufacturing companies supported by the CLIÉ Remote Commander application . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 3 What you can do with the CLIÉ Remote Commander The CLIÉ Remote Commander is an application you can install on your CLIÉ handheld to enable the CLIÉ handheld to function as a remote commander. A single remote control for multiple devices You can control a variety of remote-controlled devices (e. g. adjusting the TV volume), since you do not even have to take out the stylus to operate. 1 On the Application Launcher screen, rotate the Jog DialTM navigator to select CLIÉ RMC and then press the Jog Dial navigator. Or, tap the CLIÉ RMC icon on the Application Launcher screen. CLIÉ Remote Commander starts and the control screen of the last used device is displayed. 2 3 Tap Menu . Chapter 4 Tap Key Assignment from the Options menu. The Key Assignment screen appears. 4 If the check box for Use Key Assignment at the bottom right corner is not selected, tap to select it. If the check box is unmarked, application buttons and Jog Dial navigator cannot be used in the CLIÉ Remote Commander application even if operations are assigned to them. Continued on next page 9 Preparing the CLIÉ Remote Commander for your use 5 Tap the box next to each assignable button (e. g. JOG Up). The Key Assignment dialog box for each button appears. 6 7 8 9 Tap the arrow V next to Entry, and select the name of the remote control setting you wish to assign to the key. Tap the arrow V next to Function, and select the operation you want to assign to that button. Repeat steps 3 to 8 until you have finished setting all the functions that you want. Chapter 4 10 Using the CLIÉ handheld as a remote commander You can operate a remote-controlled device on the device's control screen. For those operations you have assigned to the Jog DialTM navigator or to the application buttons, see page 9. Notes · Be sure to point the IR port of your CLIÉ handheld toward the device that you wish to remote-control. · The reach of the remote-control signal is approximately 5 meters, but it may vary depending on the receiving device or on the environment. Remote-controlling a device Operating a device from the control screen 1 On the Application Launcher screen, rotate the Jog DialTM navigator to select CLIÉ RMC and press the Jog Dial navigator. Or, tap the CLIÉ RMC icon on the Application Launcher screen. CLIÉ Remote Commander application starts and control screen for the last used device appears. Note If the setting for the last used device has been deleted, the Select Control screen appears. Chapter 4 2 Perform either of the following to switch to the control screen of the device you are about to remote-control. · For devices assigned to a quick-start button: Tap the quick-start button to which it is assigned. [. . . ] Or, tap the CLIÉ RMC icon on the Application Launcher screen. CLIÉ Remote Commander application starts and control screen for the last used device appears. Note If the setting for the last used device has been deleted, the Select Control screen appears. Chapter 4 2 Perform either of the following to switch to the control screen of the device you are about to remote-control. · For devices assigned to a quick-start button: Tap the quick-start button to which it is assigned. · For devices unassigned to a quick-start button: Tap Select, then tap to select the name of the remote control setting from the list. The control screen for the selected device appears. 3 Tap the on-screen buttons to remote-control the device. 11 Using the CLIÉ handheld as a remote commander Operating devices directly with the Jog Dial navigator or the application button Follow the steps below to perform the assigned operation from the Jog Dial navigator or the application buttons. 1 2 Start CLIÉ Remote Commander. [. . . ]