User manual SONY CMT-FX200

[. . . ] Unit Getting Started Listening to the radio 1 Select "TUNER FM" or "TUNER AM. " Press TUNER/BAND repeatedly. To select a memory on the USB device 2 Perform tuning. For automatic scanning Press TUNING MODE repeatedly until "AUTO" appears, and then press +/ . Scanning stops automatically when a station is tuned in, and "TUNED" and "ST" (for stereo programs only) light up in the display. If the USB device has more than one memory (for example, internal memory and a memory card), you can select which memory to use and then start playback. Use buttons on the unit to select a memory on the USB device. 1 Press FUNCTION repeatedly to select the USB function. 2 Connect the USB device to the (USB) port . 4 Press / repeatedly to select a memory Remote FM lead antenna (Extend it horizontally. ) AM loop antenna To right speaker To wall outlet Speaker cord (Red/) Speaker cord (Black/) To left speaker If "TUNED" does not light up and the scanning does not stop, press to stop scanning, then perform manual tuning (below). [. . . ] If the issue persists, contact your nearest Sony dealer. A problem has been detected with the level of electrical current from the (USB) port . If this display pattern persists, contact your nearest Sony dealer. To improve tuner reception Turn off CD player/USB device power by using the system's power management function. Use buttons on the unit to turn off the CD player/USB device power. Precautions Discs that this system CAN play Audio CD CD-R/CD-RW (audio data/MP3 files) Specifications Mainunit Amplifiersection European and Russian models: DIN power output (rated): 4 watts + 4 watts (4 ohms at 1 kHz, DIN) Continuous RMS power output (reference): 5 watts + 5 watts (4 ohms at 1 kHz, 10% THD) Music power output (reference): 9 watts + 9 watts Other models: DIN power output (rated): 4 watts + 4 watts (4 ohms at 1 kHz, DIN) Continuous RMS power output (reference): 5 watts + 5 watts (4 ohms at 1 kHz, 10% THD) There is no sound. 1 Press FUNCTION repeatedly to select the CD function. 3 Select the desired track or file number. Press / repeatedly until the desired track or file number appears. When programming MP3 files, press + / repeatedly to select the desired folder, and then select the desired file. Selected track or file number Total playing time of the selected track or file * For example, you can view CD/MP3 disc information or the USB device information, such as; track or file number during normal play. total playing time and total number of tracks on the CD-DA disc (only when normal play mode is selected and the player is stopped). total number of folders (albums) on the MP3 disc or the USB device (only when normal play mode is selected and the player or the USB device is stopped). volume label if it exists on the MP3 disc or the USB device (only when normal play mode is selected and the player or the USB device is stopped). If "PROTECT" appears on the display The USB device is not connected correctly. Turn off the system, then reconnect the USB device. Immediately unplug the power cord, and check the following items after "PROTECT" disappears. After you have checked these above items and found to be all right, reconnect the power cord, and turn on the system. If the issue persists, contact your nearest Sony dealer. There is noise, skipping, or distorted sound. 2 Press to turn off the system. 3 After "STANDBY" stops flashing, press DISPLAY Discs that this system CANNOT play Turn off the system, then reconnect the USB device. Noise may have been entered when creating music data due to the conditions of the computer. Send files encoded with higher bit rates to the USB device. 4 Program the selected track or file. Press ENTER to enter the selected track or file. General The system does not turn on. Is the power cord plugged in? "READING" is displayed for an extended time, or it takes a long time before playback starts. The reading process can take a long time in the following cases. The internal memory is fragmented. to display the clock and then press while holding down , until "CD/USB PWR OFF" appears. In addition, when the tuner function is selected, power is not supplied to the USB device, so it is not recognized and charged even if connected. To turn on CD player/USB device power, repeat the procedure until "CD/USB PWR ON" appears. To reset the system to factory settings Notes on the display information 5 Repeat steps 3 through 4 to program additional tracks or files, up to a total of 25 tracks or files. 6 To play your program of tracks or files, press . The program remains available until you open the CD compartment. To play the same program again, press . To cancel Program Play Press PLAY MODE repeatedly until "PGM" disappears while the player is stopped. To delete the last track or file of the program Press CLEAR while the player is stopped. To view program information, such as total track number of the program Press DISPLAY repeatedly. Characters that cannot be displayed appear as "_". The following are not displayed; total playing time for an MP3 disc and a USB device. The following are not displayed correctly; elapsed playing time of an MP3 file encoded using VBR (variable bit rate). folder and file names that do not follow either the ISO9660 Level 1, Level 2 or Joliet in the expansion format. ID3 tag information for MP3 files when ID3 version 1 and version 2 tags are used (ID3 version 2 tag information display has priority when both ID3 version 1 and version 2 tags are used for a single MP3 file). up to 32 characters of ID3 tag information using uppercase letters (A to Z), numbers (0 to 9), and symbols ( $ % ' ( ) * + , ­ . [. . . ] Be careful when placing the unit or speakers on surfaces that have been specially treated (for example, with wax, oil, polish) as staining or discoloration of the surface may result. If the system is brought directly from a cold to a warm location or is placed in a very damp room, moisture may condense on the lens inside the CD player, and cause the system to malfunction. In this situation, remove the disc, and leave the system turned on for about an hour until the moisture evaporates. General On heat buildup 4 Set the time to start playback. Press / repeatedly to set the time, then press ENTER . Tuner Severe hum or noise, or stations cannot be received. ("TUNED" or "ST" flashes on the display. ) Heat buildup on the unit during operation is normal and is not cause for alarm. [. . . ]