User manual SONY CMT-FX300I annexe 2

[. . . ] Unit Getting Started Listening to the radio 1 Select "TUNER FM" or "TUNER AM. " Press FUNCTION +/ repeatedly. Notes 2 Perform tuning. For automatic scanning Press TUNING MODE repeatedly until "AUTO" appears, and then press + / . Scanning stops automatically when a station is tuned in, and "TUNED" and "ST" (for stereo programs only) light up in the display. When placing or removing the iPod, handle the iPod in the same angle as that of the iPod connector on the unit and do not twist or sway the iPod to prevent connector damage. When placing or removing the iPod, brace the unit with one hand and take care not to press the controls of the iPod by mistake. Hold down / to fast-forward (fast-rewind) while playing video if / does not function. [. . . ] The internal memory is fragmented. To turn off the automatic standby function On safety iPodsection 2 Turn down the volume. Press VOLUME . 5 Use the same procedure as in step 4 to set the time to stop playback. CD/MP3 player The sound skips, or the disc will not play. Wipe the disc clean, and replace it. Move the system to a location away from vibration (for example, on top of a stable stand). Move the speakers away from the system, or place them on separate stands. At high volume, speaker vibration may cause the sound to skip. This system is equipped with an automatic standby function. With this function, the system enters standby mode automatically in about 30 minutes when there is no operation or audio signal output. STBY ON" appears. Notes AUTO STANDBY" lights up in the display when the automatic " standby function is turned on. e automatic standby function is invalid for the tuner functions Th (FM/AM), even when "AUTO STANDBY" lights up in the display. e system may not enter standby mode automatically in the Th following cases; when an audio signal is detected. while the preset Play Timer or Sleep Timer is in process. 3 Select the AUDIO IN function. Press FUNCTION +/ repeatedly. 6 Select the sound source. Press / repeatedly until the desired sound . source appears, then press Erroneous display Completely disconnect the power cord (mains lead) from the wall outlet (mains) if it is not going to be used for an extended period of time. Should any solid object or liquid get into the system, unplug the system, and have it checked by qualified personnel before operating it again. The AC power cord can be changed only by a qualified service facility. Compatible iPod models: 4 Start playback. Start playback of the connected component and adjust the volume. Note The system may enter standby mode automatically if the volume level of the connected component is too low. See "To turn off the automatic standby function. " 7 Turn off the system. Press . Do not operate the system from the time the system turns on until the playback starts. Send the music data to the USB device again, as the data stored in the USB device may have been corrupted. The character codes that can be displayed by this system are numbers and alphabets only. Other characters are not displayed correctly. iPod nano 5th generation (video camera) On placement Play does not start from the first track. The USB device is not recognized. To check the setting Return to Normal Play by pressing PLAY MODE repeatedly until both "PGM" and "SHUF" disappear. Adjusting the sound To Adjust the volume Generate a more dynamic sound (Dynamic Sound Generator X-tra) Set the sound effect Press VOLUME +/ . 2 Press / repeatedly to select "SELECT, " and then press . Starting playback takes more time than usual. 3 Press / repeatedly to select "PLAY SEL, " and then press . To cancel the timer EQ . Repeat the same procedure as above until "OFF" appears . in step 3, and then press The following discs can increase the time it takes to start playback; a disc recorded with a complicated tree structure. a disc that has not been finalized (a disc to which data can be added). a disc that has many folders. Turn off the system and reconnect the USB device, then turn on the system. Check the information on the websites about compatible USB devices with URLs listed under "Playing a file of the USB device. " The USB device does not work properly. Refer to the USB device operation manual for how to deal with this problem. Play does not start. iPod There is no sound. Make sure the iPod is connected securely. [. . . ] If you use both timers, the Sleep Timer has priority. The clock setting or the Play Timer operation has been cancelled unexpectedly. To cancel Program Play Press PLAY MODE repeatedly until "PGM" disappears while the player is stopped. If about a minute elapses with no operation, the clock setting or Play Timer setting is cancelled automatically. Perform the operation again from the beginning. To delete the last track or file of the program Press CLEAR while the player is stopped. Sleep Timer: To view program information, such as total track number of the program Press DISPLAY repeatedly. You can fall asleep to music. If you select "AUTO, " the system automatically turns off after the current disc or USB device stops, or within 100 minutes. There is no sound. If you connect an unsupported USB device, the following problems may occur. Check the information on the websites about compatible USB devices with URLs listed under "Playing a file of the USB device. " The USB device is not recognized. [. . . ]