User manual SONY CMT-FX350I

[. . . ] Unit Getting Started Listening to the radio 1 Select "DAB" or "TUNER FM. " Press FUNCTION +/ repeatedly. Playing the iPod 1 Select the iPod function. Press FUNCTION +/ repeatedly. 2 Perform tuning. For automatic scanning Press TUNING MODE repeatedly until "AUTO" appears, and then press + / . Scanning stops automatically when a station is tuned in, and "ST" (for stereo programs only) lights up in the display. 2 Place the iPod. 3 Start playback. Press . To control the iPod To Pause playback Scroll up/down the iPod menus Select a track or chapter of audiobook/ podcast Choose the selected item Find a point in a track or chapter of audiobook/ podcast Return to the previous menu or select a menu Press / . / . If the scanning for an FM station does not stop, press to stop scanning, then perform manual tuning (below). [. . . ] You can select normal play (" " for all MP3 files in the folder on the disc), shuffle play ("SHUF" or " SHUF*" for folder shuffle), or program play ("PGM"). * When playing a CD-DA (audio) disc, same operation as normal (SHUF) Play. (SHUF) Play performs the Using optional audio components 1 Prepare the sound source. Connect additional audio component to the AUDIO IN jack on the unit using an audio analog cord (not supplied). Using the timers The system offers two timer functions. If you use both timers, the Sleep Timer has priority. Troubleshooting 1 Make sure the power cord and speaker cords are correctly and firmly connected. iPod There is no sound. Make sure the iPod is connected securely. Adjust the volume. Messages FULL : You tried to program more than 25 tracks or files (steps). NO DISC : There is no disc in the player, or you have loaded a disc that cannot be played. NO SERV (DAB only) : There is no supported DAB broadcast in your country or region. No TEXT (DAB only) : There is no text information in the received service. NOT USED : You tried to perform a specific operation under conditions where that operation is prohibited. OVER : You have reached the end of the disc while pressing during playback or pause. TIME NG : The Play Timer start and end times are set to the same time. Specifications Mainunit Amplifiersection UK model: DIN power output (rated): 4 watts + 4 watts (4 ohms at 1 kHz, DIN) Continuous RMS power output (reference): 5 watts + 5 watts (4 ohms at 1 kHz, 10% THD) Music power output (reference): 9 watts + 9 watts Australian model: DIN power output (rated): 4 watts + 4 watts (4 ohms at 1 kHz, DIN) Continuous RMS power output (reference): 5 watts + 5 watts (4 ohms at 1 kHz, 10% THD) Speaker Speaker system: Full range, 8 cm dia. , cone type Rated impedance: 4 ohms Dimensions (W/H/D): Approx. 1. 23 kg net per speaker General Sleep Timer: 2 Turn down the volume. Press VOLUME . 3 Select the AUDIO IN function. Press FUNCTION +/ repeatedly. You can fall asleep to music. If you select "AUTO, " the system automatically turns off after the current disc stops, or within 100 minutes. 2 Find your problem in the checklist below, and take the indicated corrective action. If the issue persists, contact your nearest Sony dealer. The sound is distorted. If "PROTECT" appears on the display Make sure the iPod is connected securely. Set the "EQ" setting of the iPod to "Off " or "Flat. " Power requirements: UK model: AC 230 V, 50/60 Hz Australian model: AC 230 V 240 V, 50/60 Hz Power consumption: 28 watts Dimensions (W/H/D) (excl. 2. 3 kg Supplied accessories: Remote Commander (1), DAB/FM lead antenna (1) Design and specifications are subject to change without notice. 4 Start playback. Start playback of the connected component and adjust the volume. Note The system may enter standby mode automatically if the volume level of the connected component is too low. See "To turn off the automatic standby function. " Play Timer: You can wake up to CD, DAB/FM reception or iPod at a preset time. Make sure you have set the clock. 1 Prepare the sound source. Prepare the sound source, and then press VOLUME +/ to adjust the volume. To start from a specific CD track or audio file, create your own program. Immediately unplug the power cord, and check the following items after "PROTECT" disappears. After you have checked these above items and found to be all right, reconnect the power cord, and turn on the system. If the issue persists, contact your nearest Sony dealer. The iPod does not function. Input Make sure the iPod is connected securely. Because the operation of the system and the iPod are different, you may not operate the iPod using buttons on the remote or unit. In this case, use the control buttons on the iPod. AUDIO IN (stereo mini jack): Sensitivity 550 mV, impedance 50 kilohms PHONES (stereo mini jack): Accepts headphones with an impedance of 8 ohms or more SPEAKERS: Accepts impedance of 4 ohms Outputs Standby power consumption: 0. 5 W Halogenated flame retardants are not used in the certain printed wiring boards. CDplayersection The iPod cannot be charged. Adjusting the sound To Adjust the volume Generate a more dynamic sound (Dynamic Sound Generator X-tra) Set the sound effect Press VOLUME +/ . DSGX on the unit. 2 Select the timer set mode. Press TIMER MENU . 3 Set the play timer. Press / repeatedly to select "PLAY SET, " then . [. . . ] At high volume, speaker vibration may cause the sound to skip. 2 Press to turn off the system. 3 After "STANDBY" stops flashing, press DISPLAY Before playing, wipe the disc with a cleaning cloth from the center out to the edge. Do not clean discs with solvents, such as benzine, thinner, or commercially available cleaners or antistatic spray intended for vinyl LPs. Do not expose discs to direct sunlight or heat sources such as hot air ducts, nor leave it in a car parked in direct sunlight. iPodsection Compatible iPod models: On safety to display the clock, and then press while holding down , until "CD POWER OFF" appears. [. . . ]