User manual SONY DAV-DZ310

[. . . ] Do not expose batteries or apparatus with battery-installed to excessive heat such as sunshine, fire or the like. To prevent injury, this apparatus must be securely attached to the floor/wall in accordance with the installation instructions. Instead it shall be handed over to the applicable collection point for the recycling of electrical and electronic equipment. By ensuring this product is disposed of correctly, you will help prevent potential negative consequences for the environment and human health, which could otherwise be caused by inappropriate waste handling of this product. [. . . ] This effect is activated automatically when all the following conditions are satisfied: ­ The function is set to "AUDIO IN" or "USB. " ­ "SUR. SETTING" is set to "A. F. D. MULTI" (page 48). To turn off the sound effect Select other than "A. F. D. MULTI" for "SUR. SETTING" (page 48). 50GB 1 Convenient Functions Make sure that the system and your TV are connected with an HDMI cable. Switch the input selector on your TV so that the signal from the system through the HDMI input appears on the TV screen. Set the Control for HDMI function of your TV. 2 3 4 Using the Control for HDMI Function for "BRAVIA" Sync This function is available on TVs with the "BRAVIA" Sync function. By connecting Sony components that are compatible with the Control for HDMI function with an HDMI cable, operation is simplified as below: ­ System Power Off (page 51) ­ One-Touch Play (page 52) ­ Theatre Mode (page 52) ­ System Audio Control (page 52) ­ Volume Limit (page 52) ­ Audio Return Channel (page 52) ­ Remote Easy Control (page 52) ­ Language Follow (page 53) Control for HDMI is a mutual control function standard used by CEC (Consumer Electronics Control) for HDMI (High-Definition Multimedia Interface). Note For details of the setting of your TV, refer to the operating instructions of your TV. 5 6 7 8 9 On the system, press DVD/CD. [SETUP], Convenient Functions Press X/x to select [CUSTOM], then press . . 10 Press X/x to select [CONTROL FOR 11 Press X/x to select [ON], then press Turning the system off in sync with your TV (System Power Off) When you turn your TV off by using the POWER button on your TV's remote or TV [/1 on the system's remote, the system turns off automatically. Note · Depending on the connected component, the Control for HDMI function may not work. Refer to the operating instructions of the component. Preparing the Control for HDMI function (Control for HDMI - Easy Setting) If your TV is compatible with the Control for HDMI - Easy Setting function, you can set the system's [CONTROL FOR HDMI] function automatically by setting your TV. If your TV is not compatible with the Control for HDMI - Easy Setting function, set the Control for HDMI function of the system and TV manually. · This function depends on the settings of your TV. while playing a CD), the system may not turn off automatically. 51GB Watching a DVD by a single button press (One-Touch Play) Press ONE-TOUCH PLAY screen and the front panel display of the system may differ. Tip · You can also operate the System Audio Control function via the TV menu. · "STBY OFF": You cannot receive the system's sound by the S-AIR receiver while the unit is in standby mode. · "PARTY": You can set the S-AIR receiver to output the same sound as the main unit. · "SEPARATE": You can set the S-AIR receiver to output the sound selected via the S-AIR receiver itself. 4 Note Press SYSTEM MENU. 4 5 Press SYSTEM MENU. When you select "SEPARATE" in Step 3, press S-AIR CH on the S-AIR receiver to select the function. · When you turn the system off while "S-AIR STBY" is set to "STBY ON, " "S-AIR" flashes (when wireless transmission between the unit and S-AIR receiver is not activated), or lights up (when wireless transmission between the unit and S-AIR receiver is activated) in the front panel display. The S-AIR receiver's function changes as follows. "MAIN UNIT" t "TUNER FM" t "AUDIO IN" t . . . To enjoy the same function as the main unit, select "MAIN UNIT. " Identifying the unit with a specific S-AIR sub unit (Pairing operation) For the surround amplifier For the S-AIR receiver When using S-AIR products, neighbors may also receive your system's sound if IDs are the same, or you may receive sound from neighbors. To prevent this, you can identify the unit with a specific S-AIR sub unit by performing the pairing operation. 6 Adjust the volume on the S-AIR receiver. 55GB When you perform pairing, wireless transmission is activated between the paired main unit and S-AIR sub unit only. Note 1 2 Place the S-AIR sub unit that you want to pair near the unit. Match the IDs of the unit and the S-AIR sub unit. · Perform pairing within several minutes of Step 5. If you do not do so, "PAIRING" and "INCOMPLETE" appear alternately in the front panel display. To cancel pairing, press SYSTEM MENU. 7 Press SYSTEM MENU. · To set the ID of the unit, see "To set the ID of the unit" (page 54). · To set the ID of the surround amplifier, refer to the operating instructions of the surround amplifier. · To set the ID of the S-AIR receiver, refer to the operating instructions of the S-AIR receiver. To cancel pairing Change the ID of the main and sub unit (page 54). 3 4 If wireless transmission is unstable For the surround amplifier For the S-AIR receiver If you use multiple wireless systems, such as wireless LAN or Bluetooth, the transmission of S-AIR signals or other wireless signals may be unstable. [. . . ] · Make sure that the connected component is compatible with the [CONTROL FOR HDMI] function. · Check the connected component's setting for the Control for HDMI function. · If you change the HDMI connection, connect and disconnect the AC power cord (mains lead), or have a power failure, set [CONTROL FOR HDMI] in [HDMI SETUP] to [OFF], then set to [ON] (page 64). · For details, see "Using the Control for HDMI Function for "BRAVIA" Sync" (page 51). [. . . ]