User manual SONY HCD-C33

[. . . ] The CLASS 1 LASER PRODUCT MARKING is located on the rear exterior. INFORMATION This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. [. . . ] m x > M 2 VOLUME TAPE m/M 3 DOLBY NR 16 1 Tips Press TAPE EJECT Z and insert a recorded tape into the cassette holder. With the side you want to play facing towards you Z bB m X x M z · If you press TAPE nN when the power is off, the system automatically turns on and starts playing the tape if there is a tape in the holder (One Touch Play). · To switch to the tape while listening to another source, press TAPE nN while the tape is stopped. The tape will automatically start playing (Automatic Source Selection). · To play a tape recorded with the Dolby NR system, press DOLBY NR on the remote before step 4. ";" appears. Basic Operations 2 3 Press TAPE. "TAPE" appears. Press DIR MODE on the remote repeatedly to select " " to play one side of the tape, " "to play both "* to play both sides sides, or " repeatedly. * The tape automatically stops after playing back five times. 4 Press TAPE nN. The tape starts playing. The reverse side will begin playing. To Stop playback Pause Fast-forward or rewind Remove or replace the tape Adjust the volume Do this Press TAPE x. Turn VOLUME. 17 The CD Player Checking the remaining playing time on the CD Do the procedure below to check the remaining playing time of the current track or the entire CD. Playing CD tracks repeatedly -- Repeat Play The Repeat Play function lets you playback a single track or all the tracks on a CD repeatedly in Normal Play. You can also use Repeat Play function while in Shuffle Play or Program Play. DISPLAY + ­ Z u . m x > M , Press DISPLAY. Each time you press this button, the display changes as follows: REPEAT During playback t Current track number and elapsed playing time of the track r Current track number and remaining playing time of the track r Remaining playing time of the entire CD r Clock display , Press REPEAT repeatedly during playback until "REPEAT" appears. Repeat Play starts. The following table describes the two repeat modes. To repeat All the tracks on the CD Only the currently playing track Press REPEAT repeatedly until "REPEAT" appears. REPEAT repeatedly until "REPEAT 1" appears. Tip Each time you press DISPLAY while the CD (or tape) is stopped, the display changes as follows: t Total playing time r Clock display r Current source display To cancel Repeat Play Press REPEAT repeatedly until "REPEAT" and "REPEAT 1" disappear. Note If the CD contains 25 tracks or more, the remaining playing time of the current track will appear as "- - - . Press S on the remote where you want the system to begin recording on the side facing away from you. When the system detects this command, the CD pauses, the tape reverses direction, and then the system resumes recording with the next CD track on the tape side facing away from you. 1, 2 5, 7 6 9 9 12 DOLBY NR 22 Other Features 10 Repeat steps 6 and 7 to select tracks to be recorded on the side of the tape facing away from you. Adjusting the sound Not only can you adjust the bass and treble, you can use the DSG (Dynamic Sound Generator) function to enjoy a more powerful sound. BASS DSG TREBLE 11 Press CD SYNC. The tape stands by for recording and the CD stands by for playback. " " and "B" (or "b") appear, and the CD SYNC indicator lights up. Z bB x M z 12 Press DIR MODE on the remote repeatedly to select " " to record on " one side of the tape, or " "or " to record on both sides. m X The Tape Deck Deck/Other Features The Tape + ­ 13 Press TAPE X. Recording starts. Z u . m x > M To stop recording Press TAPE x. To cancel Program Edit Press PLAY MODE repeatedly until "PGM" disappears. Tips · To record with the Dolby NR system on, press DOLBY NR on the remote before step 13. · To start recording on the side facing away from you, after doing step 11, press TAPE nN until " " changes to " ". Generating a more dynamic sound , Press DSG. To cancel the DSG Press DSG again. Adjusting the bass , Turn BASS. You can adjust the bass in 7 steps (+3 ~ 0 ~ ­3). Adjusting the treble , Turn TREBLE. You can adjust the treble in 7 steps (+3 ~ 0 ~ ­3). 23 Using the Radio Data System (RDS) (European model only) Falling asleep to music -- Sleep Timer The Sleep Timer function lets you specify a sleep time, after which the system stops playing and turns off automatically. You can thus fall asleep to music. What is the Radio Data System? Radio Data System (RDS)* is a broadcasting service that allows radio stations to send additional information along with the regular program signal. Note RDS may not work properly if the station you have tuned in is not transmitting the RDS signal properly or if the signal is weak. * Not all FM stations provide RDS service, nor do they all provide the same types of services. If you are not familiar with the RDS system, check with your local radio stations for details on RDS services in your area. SLEEP , Press SLEEP. Each time you press this button, the sleep time changes as follows: AUTO t 90MIN t 80MIN t 70MIN R r OFF T 10MIN . . . . T 60MIN Receiving RDS broadcasts , Simply select a station from the FM band. When you tune in a station that provides RDS services, the station name appears in the display. When you choose "AUTO" The system turns off after the current CD or tape finishes playing (up to 100 minutes). [. . . ] For details, refer to the instructions of the cleaning cassette. General There is no sound from the speakers. Set the clock (see page 6) and timer settings (see pages 25 and 26) again. "c DAILY" and "c REC" do not appear when you press TIMER SELECT on the remote. · Move the speakers farther away from the TV set. Additional Information Demagnetizing the tape heads Demagnetize the tape heads and the metal parts that have contact with the tape after every 20 to 30 hours of use with a commercially available demagnetizing cassette. [. . . ]