User manual SONY ICF-C717PJ

[. . . ] 4-180-722-31(1) FM/AM Clock Radio Operating Instructions For customers who purchased this product in the USA Please register this product on line at http://www. sony. com/productregistration. Proper registration will enable us to send you periodic mailings about new products, services, and other important announcements. Registering your product will also allow us to contact you in the unlikely event that the product needs adjustment or modification. Thank you. Important Safety Instructions 1) 2) 3) 4) 5) 6) 7) Read these instructions. [. . . ] Otherwise, the 100-year calendar, current time, alarm, and station presets will be erased. If the clock is erased while you are replacing the battery, set the clock again. (See "Setting the clock") Features Dual alarm FM/AM synthesized clock radio Nature Sounds (Sea Waves, Birds, Rain, Brook, Under the Sea) Room temperature display (Fahrenheit / Centigrade) 5°F ­ 122°F (­15°C ­ 50°C) Built-in audio cable for Digital Music Player 10 Station Presets (5 FM/5 AM) Various types of alarms - radio, buzzer and Nature Sounds (5) Automatic time set: when you plug the clock in for the first time, the current time will be shown in the display Automatic Daylight Saving Time Set/Summer time adjustment 100-year calendar and DATE/TIME ZONE button to display year, month, and date Brightness Control (High/Low/Off) No Power No Problem alarm system to keep the clock and the alarm operating during a power interruption with a CR2032 battery installed Extendable Snooze system - Snooze time can be set from 10 to 60 minutes Progressive Alarm Speed (buzzer only) 3 Connect the cords to the AM antenna terminals. Cord (A) or cord (B) can be connected to either terminal. Insert the cord while pushing down the terminal clamp. To cancel Automatic DST/Summer Time adjustment during daylight saving time (summer time) WARNING Replace the battery for the clock backup with a Sony CR2032 lithium battery. Icons Sound type Sea Waves Birds Rain Brook Under the Sea Note When other functions are in use, Nature Sounds are not available. 3 Press TIME SET + or ­ repeatedly to 4 5 The year starts to flash in the display. Setting the radio alarm 1 Perform steps 1 to 5 in "To set the alarm. " 2 Press TIME SET + or ­ to select "RADIO" alarm mode, and press ALARM ON/OFF A or B. To doze for a few more minutes Built-in audio cable The seconds advance from zero. Notes While setting the clock, you must perform each step within 65 seconds, or the clock setting mode will be canceled. When pressing any of the rear buttons, hold the unit firmly to prevent slippage. set the year. Repeat steps 3 and 4 to set the month, day, hour and minute, and then press DISPLAY/CLOCK. 3 Press TIME SET + or ­ to select the "RADIO" appears in the display. Press SNOOZE / BRIGHTNESS. The sound turns off but will automatically come on again after about 10 minutes. You can change the snooze time by pressing SNOOZE / BRIGHTNESS repeatedly within 4 seconds. The maximum snooze time is 60 minutes. Using the temperature function This unit includes an external temperature sensor, allowing you to monitor ambient temperature. To switch between Fahrenheit and Centigrade, press and hold the SNOOZE / BRIGHTNESS and DATE/TIME ZONE buttons for more than 2 seconds. Notes In the example, the display shows Fahrenheit; however, Centigrade can also be displayed. Improper use of the external temperature sensor may cause a malfunction. Do not place the temperature sensor near the floor, a heat source such as a radiator or airduct, or in a place subject to direct sunlight. The display temperature and actual temperature may differ depending on the usage environment. The operating temperature range is 5 °F (­15 °C) to 122 °F (50 °C). If the temperature is lower than 5 °F (­15 °C) or higher than 122 °F (50 °C), the "Lo" or "Hi" indicator appears. When plugging in the unit or recovering from a power interruption, the temperature display of this unit will flash "--". The temperature will be displayed after 20 seconds. To stop the alarm Tuning in to a station AM band, FM band or the last station, and press ALARM ON/OFF A or B. The unit automatically scans AM or FM stations. 4 Press TIME SET + or ­ to select the 5 If you select the last station, jump to step 5. Press OFF ALARM RESET to turn off the alarm. The alarm will sound again at the same time the next day (if the setting is not changed). 1 Press RADIO BAND to turn on the 2 Press and hold TUNING + or ­. radio to select the AM or FM band. + : scans upward through the frequency bands. When a station is received, scanning stops. station, and press ALARM ON/OFF A or B. Press TIME SET + or ­ to adjust the volume, and press ALARM ON/OFF A or B. The setting is entered. To deactivate the alarm Press ALARM ON/OFF A or B to turn off the ALARM "" or "" indicator in the display. [. . . ] Press TIME SET + or ­ to set the desired minute, and press ALARM ON/ OFF A or B. Setting the sleep timer You can fall asleep to "NATURE SOUND, " "RADIO, " or "AUDIO IN" using the built-in sleep timer that turns off "NATURE SOUND, " "RADIO, " or "AUDIO IN" automatically after a preset duration. Connecting external component (See fig. ) To listen to sound 1 Connect the built-in audio cable with the stereo mini plug on the bottom of the unit to the line output jack or headphones jack on the optional component (e. g. , portable music player). Play the optional component connected to the unit's built-in audio cable. Adjust the volume using VOL + or ­ and the connected component's volume. 3 1 Press SLEEP while the unit is turned on. "SLEEP" appears and the sleep time flashes in the display. 2 Press SLEEP to set the sleep timer duration. FM wire antenna The display shows the frequency for a few seconds and then changes back to the current time. [. . . ]