User manual SONY KDF-E50A12U

[. . . ] 2-632-913-43(1) LCD Projection TV Operating Instructions Before operating the TV, please read the "Safety Information" section of this manual. Retain this manual for future reference. KDF-E50A12U KDF-E42A12U KDF-E50A12U KDF-E42A12U 2-632-913-43(1) Printed in Spain © 2005 Sony Corporation NOTICE FOR CUSTOMERS A moulded plug complying with BS1363 is fitted to this equipment for your safety and convenience. Should the fuse in the plug supplied need to be replaced, a 5 AMP fuse approved by ASTA or BSI to BS 1362 (i. e. , marked with or ) must be used. When an alternative type of plug is used it should be fitted with a 5 AMP FUSE, otherwise the circuit should be protected by a 5 AMP FUSE at the distribution board. [. . . ] appears only if the equipment is connected to the S video socket 4 instead of the video socket 4, and S video input signal is input through the S video socket 4. 5: RGB input signal through the PC connectors audio input signal through the socket 5. Press M/m/</, to change/set the setting, then press OK. To exit the menu, press MENU. To return to the last display, press <. 6: Digital audio/video signal is input through the HDMI IN 6 socket. Audio input signal is analogue only if the equipment has been connected using the DVI and audio out socket. Additional operations To Do this . Return to the normal Press DIGITAL or TV operation Access the Input signal index table Press OK. Press , to select an input source, press m/M, then press OK. Continued 19 Overview of the menus The following options are available in each menu. Also, see page in parentheses for details of each menu. 5 Timer Sleep Timer (28) Clock Set (28) Timer (28) Set Up Auto Start Up (29) Auto Tuning (29) Programme Sorting (29) Programme Labels (30) AV Preset (30) ­ Label/Skip Manual Programme Preset (30) ­ Programme/Channel/Label/AFT/Audio Filter/Skip/ATT/Confirm Digital Set Up (32) ­ Digital Tuning/Digital Set-up 6 Picture Adjustment 1 2 3 4 5 6 Picture Mode Contrast Brightness Colour Hue Sharpness Co lo u r Tone Reset Noise Reduction Iris Custom Max 50 50 0 15 Warm Auto High Select: Set: OK End: MENU 1 Picture Adjustment Picture Mode (21) Contrast/Brightness/Colour/Hue/ Sharpness (21) Colour Tone (21) Reset (22)) Noise Reduction (22) Iris (22) 2 Sound Adjustment Sound Effect (23) Treble/Bass/Balance (23) Reset (23) Dual Sound (24) Auto Volume (24) Screen Auto Format (25) Screen Format (25) RGB Center (25) Features AV2 Output (26) TV Speakers (26) PC Adjustment (27) 3 4 20 Picture Adjustment menu Picture Adjustment Picture Mode Contrast Brightness Colour Hue Sharpness Colour Tone Reset Noise Reduction Iris Custom Max 50 50 0 15 Warm Auto High You can select the options listed below on the Picture Adjustment menu. To select options, see "Navigating through menus" (page 19). Tip When you set the "Picture Mode" option to "Vivid" or "Standard, " you can adjust only "Contrast, " and "Reset. " Select: Set: OK Back: End: MENU Picture Mode Selects the picture mode. Using the Menu 1 2 Press OK to select "Picture Mode". Press m/M to select one of the following picture modes, then press OK. · Vivid: For big lighted spaces. · Custom: Allows you to store your own prefered settings. Tip You can change the picture mode by pressing repeatedly. Contrast/Brightness/Colour/Hue/Sharpness 1 2 Press OK to select the option. Press </, to set the level, then press OK. Tip "Hue" can only be adjusted for an NTSC colour signal (e. g. , U. S. A. "Brightness", "Colour", "Hue" and "Sharpness" only appear and can be adjusted if "Picture Mode" is set to "Custom". Colour Tone 1 2 Press OK to select "Colour Tone". Press m/M to select one of the following, then press OK. · Cool: Gives the white colours a blue tint. · Warm: Gives the white colours a red tint. Tip "Warm" only appears and can be adjusted if "Picture Mode" is set to "Custom". Continued 21 Reset Reset all the picture settings to the factory settings. 1 2 Noise Reduction Press OK to select "Reset". Press m/M to select "OK, " then press OK. Reduces the picture noise (snowy picture) in a weak broadcast signal. 1 2 Press OK to select "Noise Reduction". Press m/M to select "Auto", then press OK. Tip This option cannot be used for an input signal from the Y, PB/CB, PR/CR sockets of / 3. Iris Enhances the contrast for dark scenes. 1 2 Press OK to select "Iris". Press m/M to select "High", "Mid", "Low" or "Off" then press OK. 22 Sound Adjustment menu Sound Adjustment Sound Effect: Treble: Bass: Balance: Reset Dual Sound: Auto Volume: Dynamic 0 0 0 A Off You can select the options listed below on the Sound Adjustment menu. To select options, see "Navigating through menus" (page 19). Select: Set: OK Back: End: MENU Sound Effect 1 2 Press OK to select "Sound Effect". Press m/M to select one of the following sound effects, then press OK. · Natural: Enhances clarity, detail, and sound presence by using "BBE High definition Sound System*1. " · Dynamic: Intensifies clarity and sound presence for better intelligibility and musical realism by using the "BBE High definition Sound System. " · Dolby Virtual*2: Uses the TV speakers to simulate the surround effect produced by a multi channel system. · Off: Flat response. Using the Menu Tips · You can change sound effect by pressing 9 repeatedly. · If you set "Auto Volume" to "On", "Soud Effect" changes to "Natural". *1 Licensed by BBE Sound, Inc. [. . . ] · Check that the optional equipment is on and press / repeatedly until the correct input symbol is displayed on the screen. · Check the connection between the optional equipment and the TV. · When installing optional equipment, leave some space between the optional equipment and the TV. · When changing programmes or selecting digital/analogue Text, turn off any equipment connected to the scart connector on the rear of the TV. [. . . ]