User manual SONY RM-VLZ620

[. . . ] 4-170-639-12(1) Integrated Remote Commander Operating Instructions RM-VLZ620 ©2010 SonyCorporation For the customers in the U. S. A. WARNING This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. [. . . ] WhilekeepingSETheld down, press , thenrelease bothbuttons. 5 SelecttheDVDinputonthe originalremotecontrol. After data transfer is complete, the SET indicator flashes three times, and the RM-VLZ620 returns to the state in Step 4. 3flashes Note TheSETindicator lightsup. If the SET indicator flashes only once, it indicates that learning is incomplete. Repeat from Step 4 again. 3 Enter - 8 - 8. 6 RepeatSteps4and5to teachotherfunctions. 7 PressSETtofinishteaching. The SET indicator flashes three times to indicate that the setting mode has been entered. 3flashes The SET indicator turns off. To cancel the process Press SET anytime. 25 To clear the learned function from the Device Select button or SYSTEM CONTROL button 1 Press and hold SET for more than 3 seconds. Press and hold the Device Select button for more than 3 seconds, or press the SYSTEM CONTROL button you want to reset. When the learned function is cleared, the SET indicator flashes three times. The SET indicator turns off. 26 Additional Features Assigning a Channel to Each Number Button Channel selecting procedures can be programmed to the number buttons (0 ­ ) for each device mode, which allows you to select any channel number directly with a single press of a number button. Notes If another channel has already been set on a button, it will be overwritten with the new one. If the button has already learned a function, you cannot assign a channel. Once a number button has been programmed, it cannot function as a regular number button. Example: To assign a channel to number button 9 in CBL mode 1 PressandholdSETformore than3seconds. TheSET indicator lightsup. Additional Features WhilekeepingSETheld down, pressthedesired DeviceSelectbutton, then releasebothbuttons. SET/SET indicator Device Select buttons The selected Device Select button lights up. 2 Enter - - 1. The SET indicator flashes three times to indicate that the setting mode has been entered. 3flashes 3 Pressthenumberbutton Number buttons, ENTER whereyouwanttoassignthe channel. The SET indicator flashes three times. 3flashes 2 4 Enterthedesiredchannel number. Programming the RMVLZ620 Consecutive Procedures You can program a consecutive procedure and perform them by pressing just one button. You can program up to 16 consecutive steps to each of the SYSTEM CONTROL buttons (1 ­ ) or the Device Select buttons. To perform the programmed procedure: ­ Press the programmed SYSTEM CONTROL button. ­ Press and hold the programmed Device Select button for more than 2 seconds*. * If you release the button within 2 seconds, the Device Select button will function to select the device mode. Notes You can press up to four buttons among the number buttons, (dot), and ENTER. If you press any other button, the SET indicator flashes once and turns off, and the setting is canceled. If you press four buttons, the setting mode ends and the channel will be programmed. 5 PressSETtocompletethe programming. The SET indicator flashes three times, and the indicators turn off. 3flashes Notes You can now select the channel by pressing just the number 9 button. If another consecutive procedure has already been set on the button, it will be overwritten with the new one. If the button has already learned a function, the setting procedure will be canceled. Clear the learned function (page 26). To cancel the process Press and hold SET for more than 3 seconds. The indicators turn off. To clear the program 1 Press and hold SET for more than Power on the TV. 3 seconds. Press and hold the programmed number button you want to reset for more than 3 seconds. When the program is cleared, the SET indicator flashes three times and turns off. Example: To program a consecutive procedure to watch a DVD to the SYSTEM CONTROL 2 button: Power on the DVD player. Start DVD playback. 28 SET/SET indicator Device Select buttons 2 Enter - 8 - 1. The SET indicator flashes three times to indicate that the setting mode has been entered. 3flashes Additional Features 3 PressaSYSTEM CONTROL buttonorDeviceSelect buttonyouwantto program. , 8, 1 SYSTEM CONTROL buttons 4 Programaconsecutive procedure. With this example, press the buttons in sequence as below*: 1 PressandholdSETformore than3seconds. WhilekeepingSETheld down, press , thenrelease bothbuttons. VIDEO1 DVD TheSETindicator lightsup. * The procedure may differ depending on your device. Program the correct procedure for your device. 2 Notes You can press any button other than the SET or SYSTEM CONTROL buttons. [. . . ] Enables the Sleep function (when available). Cable set top box KEY DISPLAY A/B/C D GUIDE /// LIST RETURN MENU INPUT 1 ­ 9, 0, ENTER, (dot) TV POWER PAGE +/­ FAVORITES INFO OPTIONS FUNCTION Proceeds to the previous location. For example, to change to channel 5, press 0 and 5 (or, press 5 and ENTER). Displays the options menu. Satellite receiver KEY DISPLAY A B C D GUIDE /// LIST RETURN MENU INPUT FUNCTION Proceeds to the previous location. Red button Green button Yellow button Blue button Displays the program guide (EPG). [. . . ]