User manual SONY VPL-EX50 annexe 1

[. . . ] 3-293-838-13 (1) Data Projector Operating Instructions VPL-EW5 VPL-EX50/EX5 VPL-ES5 © 2008 Sony Corporation WARNING To reduce the risk of fire or electric shock, do not expose this apparatus to rain or moisture. WARNING When installing the unit, incorporate a readily accessible disconnect device in the fixed wiring, or connect the power plug to an easily accessible socket-outlet near the unit. If a fault should occur during operation of the unit, operate the disconnect device to switch the power supply off, or disconnect the power plug. Replace only with the same or equivalent type recommended by the manufacturer. [. . . ] : S t a n d a rd 80 50 Graphics High 1 Press the MENU key. The menu appears. The menu presently selected is shown as a yellow button in the column on the left. SET SETTING S m a r t A PA : Auto Input Search: Input-A Signal Sel. : Color System: Pow e r S av i n g : IR Receiver: Pa n e l Key L o ck : Lamp Timer Reset On Off Component Au t o Off F ro n t & R e a r Off Input-A 4 Make the setting or adjustment of an item. · When changing the adjustment level: To increase the number, press the v or B key. · When changing the setting: Press the v or V key to change the setting. Press the ENTER or b key to restore the previous screen. Using a MENU 29 To clear the menu Press the MENU key. The menu disappears automatically if a key is not pressed for one minute. To reset items that have been adjusted Select the item that you want to reset, and then press the RESET key on the Remote Commander. "Complete!" appears on the screen and the setting of the item that you have selected is reset to its factory preset value. Items that can be reset are: · "Contrast, " "Brightness, " "Color, " "Hue" and "Sharpness" on the "Adjust Picture. . . " menu of the PICTURE SETTING menu · "Dot Phase, " "H Size, " and "Shift" on the "Adjust Signal. . . " menu of the INPUT SETTING menu Storage of the settings The settings are automatically stored in the projector memory when the ENTER key is pressed. If no signal is input If there is no input signal, "Cannot adjust this item. " appears on the screen. Unadjustable items Items that cannot be adjusted, depending on the input signal, are not displayed on the menu. For details, see page 41. 30 Using a MENU The PICTURE SETTING Menu The PICTURE SETTING menu is used for adjusting the picture or volume. Items that can be adjusted or set depend on the kind of input signals. For details, see "Input signals and adjustable/setting items" on page 41. PICTURE SETTING Picture Mode Adjust Picture. . . Vo l u m e : S t a n d a rd Input A PICTURE SETTING ADJUST PICTURE Contrast: Brightness: Gamma Mode: C o l o r Te m p . : Input-A S t a n d a rd 80 50 Graphics High 30 Setting items Picture Mode Functions Initial setting Selects the picture mode. Set according to · Dynamic: Emphasizes the contrast to produce a the input signal "dynamic" picture. · Living: Select for viewing sports, music, digital video camera picture. · Presentation: Makes the picture suitably bright for a presentation when the signal is input from a computer. The unit can store the setting values of the following sub menu items for each picture mode separately. 80 50 50 50 Adjustments and Settings Using a Menu Adjust Picture. . . Contrast Brightness Color Hue Sharpness 30 Adjusts the picture sharpness. Set according to the input signal Gamma Mode Color Temp. The PICTURE SETTING Menu 31 Setting items Functions Initial setting DDE (Dynamic Selects the mode to play the input video signal Film according to the material. Detail · Off: Plays back the interlace format without Enhancer) conversion. · Progressive: Plays back the video picture of the interlace format converting to progressive. · Film: Plays back a smooth picture in a softwear of 22, 2-3 pull-down type like a movie. [. . . ] a: distance between the screen and the center of the lens b: distance between the floor and the center of the lens c: distance between the floor and the bottom of the adjusters of the projector x: distance between the floor and the center of the screen (free) 54 Installation Diagram VPL-EX50/EX5/ES5 Unit: mm (inches) PS a N 40 60 80 2390 (94 1/8) 2700 (106 3/8) 100 2990 (117 3/4) 3380 (133 1/8) 120 3600 (141 3/4) 4070 (160 3/8) 150 180 200 6020 (237 1/8) 6800 (267 3/4) 250 7530 (296 1/2) 8500 (334 3/4) 300 9050 (356 3/8) 10210 (402 1/8) 1180 1780 (46 1/2) (70 1/8) 2020 M 1330 (52 3/8) (79 5/8) 4510 5410 (177 5/8) (213 1/8) 5090 (200 1/2) 6110 (240 5/8) b c Based on the calculation formula given below. Based on the calculation formula given below. a (N) = {(PS × 29. 376) × 1. 03} ­ 31. 7 a (M) = {(PS × 35. 202) × 0. 97} ­ 31. 7 b = x ­ {PS × 5. 055 + (a + 31. 7) × 0. 1405 ­ 4. 5} c = x ­ {PS × 5. 055+ (a + 31. 7) × 0. 1405 ­ 4. 5 + 90. 5} VPL-EW5 (When "Aspect" on the Signal menu is set to "Full 2") Unit: mm (inches) PS a N 40 1250 (49 1/4) 60 1890 (74 1/2) 2140 (84 3/8) 80 2530 (99 5/8) 2860 (112 5/8) 100 3170 (124 7/8) 3580 (141) 120 3810 (150 1/8) 4300 (169 3/8) 150 4770 (187 7/8) 5390 (212 1/4) 180 5730 (225 5/8) 6470 (254 7/8) 200 6370 (250 7/8) 7200 (283 1/2) 250 7970 (313 7/8) 9000 (354 3/8) 300 9570 (376 7/8) 10810 (425 3/4) M 1410 (55 5/8) b c Based on the calculation formula given below. Based on the calculation formula given below. a (N) = {(PS × 31. 076) × 1. 03} ­ 31. 7 a (M) = {(PS × 37. 252) × 0. 97} ­ 31. 7 b = x ­ {PS × 4. 465 + (a + 31. 7) × 0. 1405 ­ 4. 5} c = x ­ {PS × 4. 465 + (a + 31. 7) × 0. 1405 ­ 4. 5 + 90. 5} Notes for VPL-EW5 · The projected image size is the one when "Aspect" on the Signal menu is set to "Full 2". When "Aspect" on the Signal menu is set to other than "Full 2", black bands may appear at the top and bottom or right and left of the screen. [. . . ]