User manual SPECO DVR-16/IP

[. . . ] 16 CHANNEL NETWORK READY DVR DVR-16/IP User's Manual Precautions All the safety and operation instructions should be read before the DVR-16/IP is operated. All the safety and operation instructions should be retained for future reference. Do not expose the DVR-16/IP to water or moisture and do not try to operate it in wet areas. Well-chosen cover is needed when you put the DVR-16/IP in outdoor areas. [. . . ] ¡» RS-485 Baud Rate External Devices 1 RS-485 Baud Rate 2 DSCP Speed Dome 3 CHIPER CRT. V9KRP 4 PELCO Speed Dome 5 Exit ¡» Baud rate is a number related to the speed of data transmission in your security system. The higher the baud rate, the more bits per second that are transferred. Before the data are transferred between two devices, you must ensure that both devices are configured to the same transmission rate. DSCP Speed Dome DSCP Speed Dome This sub-menu is offered to adjust the dome settings. After you are in the sub-menu, you can pan/ tilt the speed dome freely by pressing SET and the direction buttons simultaneously. 1 RS-485 ID Setup 2 Zoom 3 Brightness 4 Set Preset Point 5 Enter Speed Dome Menu 6 Exit XXX XXX RS-485 ID Setup If you want to control the DSCP Speed Dome through the front panel, you should firstly check and modify the RS-485 ID here. You can simply push the right direction button to zoom in (tele) and the left direction button to zoom out (wide). Brightness Use the right and left direction buttons to adjust the brightness of the selected dome camera. Pan/ Tilt the dome camera to the wanted position and give the preset point a number, and then press the Enter button. Enter Speed Dome Menu Press Enter on this item to go to the OSD menu of installed Speed Dome. 16 ¡» PELCO Speed Dome DVR-16/IP is capable of connecting to PELCO Speed Dome; the related settings can be adjusted here in this sub-menu. You can pan/ tilt PELCO Speed Dome by pressing SET and the direction buttons simultaneously after you are entering this sub-menu. PELCO Speed Dome 1 Protocol Setup 2 ID Setup 3 Zoom 4 Focus 5 Bfightness 6 Set Preset Point 7 Goto Preset Point 8 Enter Speed Dome Menu 9 Exit D_Type 1 Protocol Setup There are two Protocol types to choose from: D_type and P_type. Zoom Press the right direction to zoom in (tele) and the left direction button to zoom out (wide). Focus Press the right/ left direction to change focus back and forth between a near object and a far object. Brightness Use the right and left direction buttons to adjust to appropriate brightness. Set Preset Point This item allows you to set preset points through the front panel. Pan/ tilt the connected receiver to a proper position, and then press the number buttons to assign a number to the preset point. Goto Preset Point Press right/ left direction button to select the number of the wanted preset point; then press Enter to go to the selected preset point. Enter Speed Dome Menu Press Enter on this item to enter connected PELCO dome camera's OSD menu. CHIPER CRT. V9KRP CHIPER CRT. V9KRP ¡» This sub-menu allows you to set the receiver. In the sub-menu, you can pan/ tile the receiver by pressing SET and direction buttons simultaneously. Item 1~4 (ID Setup, Zoom, Focus, Brightness) Please refer to the receiver user's manual for detailed information. 1 ID Setup 2 Zoom 3 Focus 4 Brightness 5 Set Preset Point 6 Goto Preset Point 7 Set Group Dwell 8 Go Preset Group 9 Stop Preset Group 10 Exit 1 1 Set Preset Point This item allows you to set preset points through the front panel. Pan/ tilt the connected receiver to a proper position, and then press the number buttons to assign a number to the preset point. Press Enter to finish the setting. 17 Goto Preset Point Press right/ left direction button to select the number of the wanted preset point; then press Enter to go to the selected preset point. [. . . ] Specification Model Name Compression Method Video System Resolution-Live Video Resolution-Recorded Recording Rate Recording Device Video Export Recording Quality Video Input Video Looping Through Main Monitor Output Call Monitor Output Alarm Input Alarm Output Network Interface Remote Control Playback Speed Zoom Power Supply Title Alarm List Dimensions Operating Temperature DVR-16/IP Wavelet NTSC PAL 720 x 480 pixels 720 x 576 pixels 720 x 240 pixels 720 x 288 pixels Up to 60 PPS Up to 50 PPS Hot swappable HDD CD-RW Supper / High / Normal / Low BNC x 16, 1. 0 Vp-p, 75 ohm. x 16, DSUB 37 pin male (TTL level) x 1, DSUB 37 pin male, 2. 0 A / 24 V Ethernet (10 Base-T) (Optional function) RS-485 DSCP Fast Forward / Rewind (x1~x8), picture by picture Yes DC 12 V / 4 A 12 characters Up to 255 events 432 x 44 x 400mm (W x H x D) 0~40°C 39 Appendix 1: Hard Disk Error Message Some messages will be shown on the screen when the H. D. D. Power off and on again Message: No Hard Disk Symptom: No HDD has been found by the system. Check the power/ IDE bus connectors, ensure they have been connected well; and then insert the HDD again. [. . . ]