User manual SPECO DVR-4TL-160

[. . . ] ® DVR-4TL series User's Manual 00P3DG090SSEA1 Version 1. 1 00P3DG090SSEA1 User's Manual Caution and Preventive Tips · · · · · · · · Take care not to drop the unit or subject the unit to major shocks or jolts. Do not place the unit near water or in other extremely humid conditions. This unit should not be placed in a built-in installation unless proper ventilation is provided. Please check the used type of power source before you plug and operate the unit; AC100V ~AC240V is acceptable. [. . . ] Use Direction keys to move the cursor to the next or previous field, UP / DOWN to change the settings in the selected field. DST Bias The item allows user to set the amount of time to move forward from the standard time for daylight saving time. The available options are <30>, <60>, <90> and <120> minutes. 18 User's Manual 3. 5 Record Schedule / Quality Setting The Record Setup menu allows user to set recording quality, recording schedules, and other recording parameters. To setup the recording quality and schedules, you have to enter the OSD Setup Menu with correct Administrator's password. In the Main menu, move the cursor to <Record Setup> and press ENTER; the following menu is displayed. Record Setup 1. Purge Data 360×240@60PPS Standard ON 3. 5. 1 Record Mode The Record Mode is for selecting resolution and recording rate. The relative record settings, such as preset configuration, will follow the record mode setting. In normal circumstance, we recommend you to select <720x240@60PPS>, the default, for this item. Move the cursor to <Record Mode> and press ENTER, then select a Record mode using UP / DOWN keys. NOTE: After changing the Record Mode setting, the warning message "This will FORMAT ALL HARDDISKS and LOAD THE FACTORY DEFAULT CONFIG!" will be shown on the screen. Press ENTER to confirm the selection, then the unit starts to format the hard disks and load the factory default settings, or press ESC to abort. We strongly recommend to backup your programmed configuration before making any changes on Record Mode settings. NOTE: The total PPS is shared by viewing windows (by 4, 8 or 16 windows, depends on the model you have purchased), which means, even one window hasn't connected with a camera and displays no video, that window still wastes pps. But if you select <ezRecord> for setting the unit, those windows with no cameras connected to them will not be recorded, in other words, the pps will not be wasted. 19 User's Manual 3. 5. 2 Schedule Setup The Schedule Setup is used to set the day and night time, or weekend recording schedule. Select <Schedule Setup> from the Record Setup menu and press ENTER; the following menu is displayed. Schedule Setup 1. Weekend End 06:00 06:00 06:00 06:00 YES Fri 18:00 Mon 06:00 AM PM PM AM · Make appropriate changes of the start time of Day and Night Time using Direction keys. · If you want to have a weekend record, choose <YES> to enable the Weekend Schedule in advance and then set the Weekend Start/End time. · Press ESC to back to previous page. 3. 5. 3 Preset Record Configuration The <Preset Config> is used to select the preset recording quality and frame rate. In normal circumstances, we strongly suggest you set the item to <Standard>, the default. Below tables show the PPS and picture size under <Standard> in Full-D1 mode, Half-D1 mode and CIF mode, respectively: Halfl-D1 mode (NTSC: 720x240@30PPS) Normal PPS 3. 75 NTSC Normal Size 11 KB Event PPS 15 NTSC Event Size 17 KB 20 User's Manual 3. 5. 4 To Record Event Video Only If you want your DVR to record images with triggered alarm (both Alarm in and Motion) only, and stop recording under normal circumstances, then follow the steps to setup your unit: · Enter the OSD setup menu with correct password. · Select <Daytime Record> and setup this item to <No>, which means no video will be recorded during daytime. When done, repeat the process to set the <Night record> and <Weekend Record> as well. ezRecord Setup How Many Days To Record Daytime Record Night Record Weekend Record Overall Recording Condition 2 Days No No No Fair NOTE: The recorded event video can be accessed not only through the Event List but also through the Date/ Time Research using the PLAY key on the front panel. 4. Basic Operation The DVR-4TL series allows user to access some general operations through the front panel easily. [. . . ] Select <System Setup> in Main menu, then select <RS485 Setup> from the System Setup menu and press ENTER. The following menu is displayed. RS485 Setup 1 Unit ID 2 Baud Rate 3 Bits 4 Stop 5 Parity 224 9600 8 1 None 30 User's Manual The ID number must match the ID address set by the dome. Note that no two devices on the same bus should be given the same ID address, or a conflict may occur. The default DVR-4TL series RS-485 settings are 9600 Baud, 8 Data Bits, 1 Stop Bit and No Parity. [. . . ]