User manual STANDARD HORIZON CP1000C

[. . . ] No part of this publication may be reproduced or distributed in any form or by any means, or stored in a database or retrieval system, without prior written permission of the publisher. CODE: IssueB - 010305 TABLE OF CONTENTS 1. ABOUT THIS ADDENDUM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 1. 0 KEY OPERATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 1. 1 HOW THIS ADDENDUM IS ORGANIZED . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] Press [CLEAR] until the menu disappears or an easier method is to move the Shuttlepoint knob to the left until the chart page is shown. 3. 0. 4 Safety Status Bar This feature displays a status bar with six boxes showing the status of certain functions. Any warning or alarm condition is identified by the red color to indicate possible risk. Move the ShuttlePoint knob to highlight MAX FUNCTIONS and press [ENTER] or move the ShuttlePoint knob to the right. Move the ShuttlePoint knob to highlight SAFETY STATUS BAR and press [ENTER] or move the ShuttlePoint knob to the right. Press [CLEAR] until the menu disappears or an easier method is to press the ShuttlePoint knob to the left a few times. Figure 3. 0. 4 - Safety Status Bar Boxes definition is as follows: Zoom Normal: when the chart is displayed at normal scale. Zoom: red when the chart is under-zoomed out more than twice normal scale, gray otherwise. Pre-programmed settings are user selectable from Full, Medium, Low, Radar (reduces the information on the display to simulate items that would be shown on a RADAR display) Pls note this function is not actually showning RADAR information it is only showning what typically would be shown by a separate dedicated RADAR display), Tides, Custom (default mode). Move the ShuttlePoint knob to highlight SETUP and press [ENTER] or move the ShuttlePoint knob to the right. Move the ShuttlePoint knob to highlight MAP CONFIGURATIONS and press [ENTER] or move the ShuttlePoint knob to the right. Move the ShuttlePoint knob to highlight DISPLAY MODE and press [ENTER] or move the ShuttlePoint knob to the right. ADDENDUM Page 11 4. Move the ShuttlePoint knob up or down to select the preset and press [ENTER]. Press [CLEAR] or move the ShuttlePoint knob to the right until the Chart page is shown. Setting Names Buoys ID Nav-Aids Light Sectors Attention Areas Tides & Currents Seabed Type Ports & Services Tracks & Routes Underwater Objects Depth Range Depth Range Min Depth Range Max Rocks Min Rocks Max Land Elevation Data Roads Points Of Interest Lat/Lon Grid Chart Boundaries Mixing Levels Value Added Data Full On On On On On On On On On On On 0 Ft 1000 Ft 0 Ft 1000 Ft On On On On On On On Medium On Off On Off On Off Off On Off On On 0 Ft 1000 Ft 0 Ft 1000 Ft Off Off Off Off Auto Off Off Low On Off On Off Off Off Off Off Off Off On 0 Ft 1000 Ft 0 Ft 1000 Ft Off Off Off Off Off Off Off RADAR On Off On Off Off Off Off On Off Off Off 0 Ft 1000 Ft 0 Ft 1000 Ft Off Off Off Off Off Off Off Tides On Off Off Off Off On Off Off Off Off On 0 Ft 1000 Ft 0 Ft 1000 Ft Off Off Off Off Off Off Off Custom (Default values) On On On On On On On On On On On 0 Ft 1000 Ft 0 Ft 1000Ft On On On On On On On 3. 1. 1 Names Buoys ID Nav-Aids Marine Settings : Turns the Local area names On or Off. : Turns the presentation of Lights, Signals, Buoys and Beacons On or Off. : Turns the light sectors of all fixed lights, buoys and light houses On or Off. : Turns the displaying of Attention Areas (areas in which special attention by the mariner is required because of natural or man-made hazards sailing regulations and restrictions) On or Off. . When data/time is available, Tidal stream arrows are shown on the charts, indicating the direction and strength of the Tide. If no data/time is available from the GPS or the chart plotter is not in Simulation mode, the icon on the map is generic one. The color of the arrow denotes the strength of the current as follows: To control the display on the map of the marine features. Light Sectors Attention Areas Tides + Currents Seabed Type Ports + Services : : Tracks + Routes : Underwater Objects : When the chart plotter receives a valid position fix, the Tide icons are shown on the charts on the basis of the current date and time: the screen displays and changes arrows as date/time changes. Areas along the shore with facilities for mooring, downloading and uploading of ships, generally sheltered from waves and winds. Port installations are piers, wharves, pontoons, dry docks, cranes. . . ). Objects are obstructions, wrecks, cable etc. ) Turns displaying of underwater objects On or Off. Objects are obstructions, wrecks, cable etc. ) Page 12 ADDENDUM 3. 1. 2 Depth Settings Depth Range Depth Range Min Depth Range Max Rocks Min Rocks Max To control the display on the map of the depth informations. : Turns the displaying of the Depth Sounding, Bathymetric Lines and Depth Area (the sea areas included in the user selectable range of minimum and maximum depth limits). [. . . ] When the picture is shown, it is possible to display the next picture associated, if any, by pressing the ShuttlePoint knob left or right. 4. 0. 1 How to show the pictures or diagrams of a cartographic object Move the cursor over the cartographic object icon. If the object has a pictures or diagrams associated, the quick info will show a camera icon on the top bar of the window: Figure 4. 0. 1a - Example of Quick Info on object with picture Page 16 ADDENDUM Press [IMAGE] or [ENTER] for 1second to display the image on the screen or press [EXPAND] or [ENTER] to open the Full Info on the object: Figure 4. 0. 1b - Example of Full Info on object with picture On the Full Info, there will be the small camera icon on a corner of the square containing the object icon. When the picture is shown, it is possible to fit it to screen by pressing [ENTER]. When the picture is shown, it is possible to change the contrast by pressing [ZOOM IN] or [ZOOM OUT]. [. . . ]